DSL-cards
From Datateknik
(Difference between revisions)
(→Experiments with DSL cards) |
(→How to do it) |
||
| Line 72: | Line 72: | ||
#: mode atm | #: mode atm | ||
#: line-term co | #: line-term co | ||
| + | #: dsl-mode shdsl symmetric annex A | ||
| + | #: line-rate auto | ||
# Configure the ATM interface | # Configure the ATM interface | ||
| − | #: | + | #: interface ATRM 0/3/0 |
| + | #: no ip address | ||
| + | #: no atm ilmi-keepalive | ||
| + | #: ! | ||
| + | #: pvc 0/35 | ||
| + | #: encapsulation aal5snap | ||
| + | #: ! | ||
| + | #: pvc 8/35 | ||
| + | #: encapsulation aal5mux ppp dialer | ||
| + | #: dialer pool-member 1 | ||
| + | # Create interface Dialer0 | ||
| + | #: interface Dialer0 | ||
| + | #: ip address 1.1.1.1 255.255.255.0 | ||
| + | #: encapsulation ppp | ||
| + | #: dialer pool 1 | ||
| + | #: dialer-group 1 | ||
| + | # Create dialer-list | ||
| + | #: dialer-list 1 protocol ip permit | ||
Revision as of 13:16, 24 March 2014
Contents |
Experiments with DSL cards
- WIC-1SHDSL and WIC-1SHDSL-V2 Documentation Roadmap
- Configuring CPE Back-to-Back Through G.SHDSL Ports
- Configuring PPP over ATM with NAT
Documentation
is it there ??
During boot
Self decompressing the image : ######################################################################################### ########################################################################################### ########################################################################################### ####################################################################### [OK] IOMEM set to: 5 Unknown Card in slot 0 PMem allocated: 381681664 bytes; IOMem allocated: 20971520 bytes ... ... Cisco 2801 (revision 7.0) with 372736K/20480K bytes of memory. Processor board ID FCZ112070FT 1 DSL controller 2 FastEthernet interfaces 2 Serial(sync/async) interfaces 1 Virtual Private Network (VPN) Module DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 62720K bytes of ATA CompactFlash (Read/Write)
Commands:
show diag
WIC/VIC/HWIC Slot 3:
GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
Hardware Revision : 0.0
Top Assy. Part Number : 800-23445-01
Board Revision : C0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC08170N9M
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier :
Product (FRU) Number :
EEPROM format version 4
show running ! controller DSL 0/3/0 !
R1(config)#controller dsL 0/3/0 R1(config-controller)#? Controller configuration commands:
default Set a command to its defaults
description Controller specific description
dsl-mode SHDSL mode
exit Exit from controller configuration mode
help Description of the interactive help system
ignore-error-duration Number of seconds errors such as CRC are ignored while
the line is training (default is 0)
line-term Customer Premise or Central Office
loopback XDSL loopback test
mode Configure the xdsl controller mode
no Negate a command or set its defaults
shutdown Shutdown the xdsl controller
snr SNR
R1(config-controller)#
How to do it
- make the DSL-controller create the ATM interface
- controller DSL 0/3/0
- mode atm
- line-term co
- dsl-mode shdsl symmetric annex A
- line-rate auto
- Configure the ATM interface
- interface ATRM 0/3/0
- no ip address
- no atm ilmi-keepalive
- !
- pvc 0/35
- encapsulation aal5snap
- !
- pvc 8/35
- encapsulation aal5mux ppp dialer
- dialer pool-member 1
- Create interface Dialer0
- interface Dialer0
- ip address 1.1.1.1 255.255.255.0
- encapsulation ppp
- dialer pool 1
- dialer-group 1
- Create dialer-list
- dialer-list 1 protocol ip permit
