DSL-cards
From Datateknik
(Difference between revisions)
(→2900 SETUP) |
(→Documentation) |
||
| Line 14: | Line 14: | ||
* FRAMTIDEN: [http://www.2mul.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/15-mt/ir-15-mt-book.pdf Broadband Access -- How To Do It] | * FRAMTIDEN: [http://www.2mul.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/15-mt/ir-15-mt-book.pdf Broadband Access -- How To Do It] | ||
* NYA KORTET: HWIC-2SHDSL [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/software/feature/guide/shdslfm.html Configuring] | * NYA KORTET: HWIC-2SHDSL [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/software/feature/guide/shdslfm.html Configuring] | ||
| − | * [http://www.cisco.com/c/en/us/support/docs/asynchronous-transfer-mode-atm/permanent-virtual-circuits-pvc-switched-virtual-circuits-svc/10480-oam.html Using OAM for PVC Management] | + | * [http://www.cisco.com/c/en/us/support/docs/asynchronous-transfer-mode-atm/permanent-virtual-circuits-pvc-switched-virtual-circuits-svc/10480-oam.html Using OAM for PVC Management], |
| + | [http://www.routerie.com/cgi-bin/ultimatebb.cgi?ubb=print_topic;f=50;t=002730 How to use "encap aal5ciscoppp virtual-temp 1"] | ||
== Laboration == | == Laboration == | ||
Revision as of 12:10, 28 April 2014
Contents |
Experiments with DSL cards
Documentation
- Pinout ? table 2, table 3
- LED description table 5
- LP off,
- CD Green when cells or frames are passing between the host and the DSLAM,
- OK green
- WIC-1SHDSL and WIC-1SHDSL-V2 Documentation Roadmap
- BAD: Configuring CPE Back-to-Back Through G.SHDSL Ports
- GOOD: ATM Mode for Two-Wire or Four-Wire SHDSL incl. Back-to-Back
- Configuring PPP over ATM with NAT
- FRAMTIDEN: Broadband Access -- How To Do It
- NYA KORTET: HWIC-2SHDSL Configuring
- Using OAM for PVC Management,
How to use "encap aal5ciscoppp virtual-temp 1"
Laboration
Laboration
- Configure Hostnames "Router2900" and "Router2600" to your routers !
- Figure out which slot your DSL card is in by using the commands:
-
Router2901#show controller shdsl
-
Router2600#show controller dsl
- Answers: 2901-Slot _____________ and 2600-Slot _____________
-
- Try the commands
show running
and find all lines that include controller and dsl on both routers- Answer: 2600 ________________
- Answer: 2901 ________________
- What is the difference between interface serial 0/0 and controller serial 0/0 ?
- How many ATM interfaces exists in show running
- Answer: ______________
2900 SETUP
- Configure the DSL controller of the 2900
- controller SHDSL 0/3/0
- description This is the CPE
- ! Automatically assign the Central Office (CO) configuration to
- ! an ATM dsl-group on the Customer Premise Equipment (CPE).
- dsl-group auto
DIDN'T WORK, PLEASE USE
controller SHDSL 0/3/0
description Can *only* run in CPE mode
dsl-group 0 pairs 0, 1
shdsl 4-wire mode enhanced
shdsl annex A
shdsl rate 4096
!
- How many ATM interfaces exists in show running
- Answer: ______________
- Configure the ATM interface of the 2900
- interface ATM 0/3/0
- no ip address
- load-interval 30
- no atm ilmi-keepalive
- Try the command show ip interface brief
- Create a ATM subinterface with a Layer2 VPI/VCI and a Layer3 IP-address
- interface ATM 0/3/0.1 point-to-point
- description Connection to Router2600 (Central Office)
- ip address 1.1.1.2 255.255.255.0
- pvc 2/100
- vbr-rt 2000 2000
- oam-pvc manage auto-detect
- encapsulation aal5mux ip
- Try the command show ip interface brief
2600 SETUP
- How many ATM interfaces exists in show running
- Answer: ______________
- Try the command show ip interface brief
- Configure the DSL controller of the 2600
- controller DSL 0/2
- description This is CO, the other end is CPE
- mode atm
- line-term co
- line-mode 4-wire enhanced
- dsl-mode shdsl symmetric annex A
- line-rate 4096
- How many ATM interfaces exists in show running
- Answer: ______________
- Configure the ATM interface of the 2600
- interface ATM 0/2
- description ATM over DSL (Central Office)
- no ip address
- load-interval 30
- no atm ilmi-keepalive
- Try the command show ip interface brief
- Create a ATM subinterface with a Layer2 VPI/VCI and a Layer3 IP-address
- interface ATM 0/2.1 point-to-point
- description Connection to Router2900 (Customer)
- ip address 1.1.1.1 255.255.255.0
- pvc 2/100
- vbr-rt 2000 2000
- no oam-pvc manage
- encapsulation aal5mux ip
- Try the command show ip interface brief
- You might get:
- ATM0/2 unassigned YES manual initializing down
- ATM0/2.1 1.1.1.1 YES manual initializing down
- Let's ping the other end !!
- Ûberkurz:
- What show-command shows the line-speed of the xDSL controller
- What show-command shows if the controller is running as CPE or CO
- What ATM AAL options are available on both cards?
- Are there any special PPP settings that are required to make communication work? Try!
- What is the theory behind the PVC's?
- Are there any special control PVC's (like 0/32 ?!?) ?
How to do it
! On 2801 running IOS (C2801-ADVIPSERVICESK9-M), Version 12.4(24)T ! #show controller dsl | inc Firmware|prog ! Firmware Version: R4.2.1 !
! Fungerar INTE ! 2801 Software (C2801-ADVIPSERVICESK9-M), Version 15.1(4)M6 ! show controll DSL | i Firm|prog ! Firmware Version: 388.132 ! DSL firmware download in progress, please wait
! make the DSL-controller create the ATM interface controller DSL 0/3/0 controller SHDSL 0/3/0 mode atm dsl-group auto ! Change to CPE on other end line-term co line-mode 2-wire line-zero dsl-mode shdsl symmetric annex A shdsl annex A line-rate auto !shdsl rate -- Only on CO side !!
! Configure the ATM interface
interface ATM 0/3/0 <-- SAME for 2901 gh.shDSL
no ip address
load-interval 30
no atm ilmi-keepalive
!
interface ATM 0/3/0.1 point-to-point
! Change to .2 on other end
ip address 1.1.1.1 255.255.255.0
pvc 2/100
vbr-rt 2000 2000
oam-pvc 0
encapsulation aal5mux ip
show atm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts
0/0.1 1 2 100 PVC MUX VBR 2000 2000 0 UP
Minimal Setup
controller DSL 0/3/0
mode atm
line-term co
interface ATM0/3/0.1 point-to-point
ip address 1.1.1.1 255.255.255.0
pvc 2/100
encapsulation aal5mux ip
Todays Errors
Hi, to force CO mode you need to configure 'termination CO' under the controller SHDSL. However, only HWIC-4SHDSL supports that command. See here for reference: "Q. Do the G.SHDSL HWICs work in central-office mode (back-to-back connection without a DSLAM)? A. Currently only the HWIC-4SHDSL supports both CPE and central-office modes for diagnostic purposes. The mode of operation can be set only from the ROM Monitor environment. CPE is the default mode of operation." [http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps7175/prod_qas0900aecd80591ff1.html http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps7175/prod_qas0900aecd80591ff1.html]
Hope this helps
Marco
Router#show diag
Slot 0:
C2610 1E Mainboard Port adapter, 4 ports
...
WIC Slot 1:
Unknown WAN daughter card
...
Product Number : WIC-1SHDSL-V2
Router#show vers | inc 12
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(8)T5, RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-i-mz.122-8.T5.bin"
Router2600#show diag
Slot 0:
C2621 2FE Mainboard Port adapter, 5 ports
...
WIC Slot 1:
Unknown WAN daughter card
Router2600#show vers | inc 12
IOS (tm) C2600 Software (C2600-BIN-M), Version 12.3(25), RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-bin-mz.123-25.bin"
show diag
WIC Slot 1:
GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
Router#show vers
Cisco IOS Software, C2600 Software (C2600-IPBASEK9-M), Version 12.4(17a), RELEASE SOFTWARE (fc2)
System image file is "flash:c2600-ipbasek9-mz.124-17a.bin"
Cisco 2621XM (MPC860P) processor (revision 1.0) with 59392K/6144K bytes of memory.
show controller atM 0/3/0 WIC Config Reg2 0x04 Gen bus error on bad G.SHDSL ATM/T1/E1 access ... Interface Serial0/3/0 Hardware is GT96K DTE Unknown (13) RX clock detected.
2901# show diag
...
WIC Slot 3:
GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
WIC module not supported/disabled in this slot
Hardware Revision : 0.0
Top Assy. Part Number : 800-23445-02
Board Revision : A0
Deviation Number : 78181
Fab Version : 04
PCB Serial Number : FOC09132CUJ
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier : V02
Product (FRU) Number : WIC-1SHDSL-V2
is it there ??
During boot
Self decompressing the image : ######################################################################################### ########################################################################################### ########################################################################################### ####################################################################### [OK] IOMEM set to: 5 Unknown Card in slot 0 PMem allocated: 381681664 bytes; IOMem allocated: 20971520 bytes ... ... Cisco 2801 (revision 7.0) with 372736K/20480K bytes of memory. Processor board ID FCZ112070FT 1 DSL controller 2 FastEthernet interfaces 2 Serial(sync/async) interfaces 1 Virtual Private Network (VPN) Module DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 62720K bytes of ATA CompactFlash (Read/Write)
Commands:
show diag
WIC/VIC/HWIC Slot 3:
GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
Hardware Revision : 0.0
Top Assy. Part Number : 800-23445-01
Board Revision : C0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC08170N9M
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier :
Product (FRU) Number :
EEPROM format version 4
show running ! controller DSL 0/3/0 !
R1(config)#controller dsl 0/3/0
R1(config-controller)#?
Controller configuration commands:
default Set a command to its defaults
description Controller specific description
dsl-mode SHDSL mode
exit Exit from controller configuration mode
help Description of the interactive help system
ignore-error-duration Number of seconds errors such as CRC are ignored while
the line is training (default is 0)
line-term Customer Premise or Central Office
loopback XDSL loopback test
mode Configure the xdsl controller mode
no Negate a command or set its defaults
shutdown Shutdown the xdsl controller
snr SNR
R1(config-controller)#
Debugging
clear
- clear interface atm 0/3/0
show
- show atm vc
- show dsl interface atm 0/3/0
* R1#show controllers dsl brief DSL 0/3/0 controller DOWN Globespan xDSL controller chipset DSL mode: Not Trained Frame mode: Utopia Configured Line rate: 2048Kbps Line Re-activated 0 times after system bootup LOSW Defect alarm: ACTIVE CRC per second alarm: ACTIVE Line termination: CO FPGA Revision: 0xB3
- show controller DSL 0/3/0
- show interfaces atm 0/3/0
debug
- debug atm events
- debug atm errors
- debug xdsl driver
???
- dslsar disable ATM0/3/0
- dslsar enable ATM0/3/0
Latest BUG hunt
show controllers dsl
! ON A CISCO 2801 Line-0 status Chipset Version: 0 Firmware Version: 388.132 Modem Status: Handshake, Status 10 Last Fail Mode: No Failure status:0x0 DSL firmware download in progress, please wait Dying Gasp: Present
! ON A 26x1 XM, IOS 12.4 Line-0 status Chipset Version: 1 Firmware Version: A29733 Modem Status: un checked mode, Status F5B9 Last Fail Mode: No Failure status:0x0 Dying Gasp: Present
! ON A 2611 XM, IOS 12.3(11)T11 Line-0 status Chipset Version: 0 Firmware Version: R3.0.1 Modem Status: un checked mode, Status DF3D Last Fail Mode: No Failure status:0x0 Dying Gasp: Present
Så här gick det till när det fungerade första gången
Router> Router>ena Router#conf t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R2-Nere R2-Nere(config)#^Z R2-Nere# R2-Nere# *Dec 16 03:11:14.075: %SYS-5-CONFIG_I: Configured from console by consolewr Building configuration... [OK] R2-Nere# R2-Nere#show running Building configuration...
Current configuration : 753 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R2-Nere ! boot-start-marker boot-end-marker ! ! no aaa new-model memory-size iomem 10 no network-clock-participate slot 1 no network-clock-participate wic 0 ip cef ! ! ! ! ! ! ! ! ! controller DSL 0/2 line-term cpe ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface Serial0/0 no ip address shutdown no fair-queue ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/1 no ip address shutdown ! ip forward-protocol nd ! ip http server no ip http secure-server ! ! control-plane ! ! line con 0 line aux 0 line vty 0 4 ! ! end
pre
R2-Nere#debug xds
R2-Nere#debug xdsl ?
application xDSL application
driver xDSL driver
eoc xDSL eoc
error xDSL error
R2-Nere#debug xdsl app
R2-Nere#debug xdsl application
xDSL application debugging is on
R2-Nere#debug xdsl driver
xDSL driver debugging is on
R2-Nere#debug xdsl error
xDSL error debugging is on
R2-Nere#
R2-Nere#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2-Nere(config)#^Z
R2-Nere#
R2-Nere#show
*Dec 16 03:12:13.227: %SYS-5-CONFIG_I: Configured from console by console contr
R2-Nere#show controllers ds
R2-Nere#show controllers dsL 0/2
DSL 0/2 controller DOWN
SLOT 0: Globespan xDSL controller chipset
DSL mode: Not Trained
No frame mode configured
Line Re-activated 0 times after system bootup
LOSW Defect alarm: ACTIVE
CRC per second alarm: ACTIVE
Line termination: CPE
FPGA Revision: 0xB2
Current 15 min CRC: 0
Current 15 min LOSW Defect: 0
Current 15 min ES: 0
Current 15 min SES: 0
Current 15 min UAS: 0
Previous 15 min CRC: 0
Previous 15 min LOSW Defect: 0
Previous 15 min ES: 0
Previous 15 min SES: 0
Previous 15 min UAS: 0
Line-0 status
Chipset Version: 0
Firmware Version: R3.0.1
Modem Status: un checked mode, Status DF3D
Last Fail Mode: No Failure status:0x0
Dying Gasp: Present
R2-Nere#
R2-Nere#show vers
Cisco IOS Software, C2600 Software (C2600-IPBASEK9-M), Version 12.4(17a), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 07-Nov-07 12:40 by prod_rel_team
ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
R2-Nere uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:c2600-ipbasek9-mz.124-17a.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
R2-Nere#show controllers dsL 0/2 | i Modem
Modem Status: un checked mode, Status DF3D
R2-Nere#show controllers dsL 0/2 | Rev
^
% Invalid input detected at '^' marker.
R2-Nere#show controllers dsL 0/2 | i Rev
FPGA Revision: 0xB2
R2-Nere#show controllers dsL 0/2
DSL 0/2 controller DOWN
SLOT 0: Globespan xDSL controller chipset
DSL mode: Not Trained
No frame mode configured
Line Re-activated 0 times after system bootup
LOSW Defect alarm: ACTIVE
CRC per second alarm: ACTIVE
Line termination: CPE
FPGA Revision: 0xB2
Current 15 min CRC: 0
Current 15 min LOSW Defect: 0
Current 15 min ES: 0
Current 15 min SES: 0
Current 15 min UAS: 0
Previous 15 min CRC: 0
Previous 15 min LOSW Defect: 0
Previous 15 min ES: 0
Previous 15 min SES: 0
Previous 15 min UAS: 0
Line-0 status
Chipset Version: 0
Firmware Version: R3.0.1
Modem Status: un checked mode, Status DF3D
Last Fail Mode: No Failure status:0x0
Dying Gasp: Present
R2-Nere#show controllers dsL 0/2 | i Firm
Firmware Version: R3.0.1
R2-Nere#show controllers dsL
DSL 0/2 controller DOWN
SLOT 0: Globespan xDSL controller chipset
DSL mode: Not Trained
No frame mode configured
Line Re-activated 0 times after system bootup
LOSW Defect alarm: ACTIVE
CRC per second alarm: ACTIVE
Line termination: CPE
FPGA Revision: 0xB2
Current 15 min CRC: 0
Current 15 min LOSW Defect: 0
Current 15 min ES: 0
Current 15 min SES: 0
Current 15 min UAS: 0
Previous 15 min CRC: 0
Previous 15 min LOSW Defect: 0
Previous 15 min ES: 0
Previous 15 min SES: 0
Previous 15 min UAS: 0
Line-0 status
Chipset Version: 0
Firmware Version: R3.0.1
Modem Status: un checked mode, Status DF3D
Last Fail Mode: No Failure status:0x0
Dying Gasp: Present
R2-Nere#
R2-Nere#
% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]:
% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]: yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]:
Press RETURN to get started!
*Mar 1 00:00:07.564: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Mar 1 00:00:21.367: %SYS-3-NOELEMENT: data_enqueue:Ran out of buffer elements for enqueue
-Process= "<interrupt level>", ipl= 6, pid= 3
-Traceback= 80F791B0 80410240 801F7060 801F7144 801E1B1C 801F424C 801F424C 801E1BDC 801F405C 801F75AC 80F8A200 80F8B5D4 80F8AB74 81ECD37C 81CB4DA4 81CB4E5C
*Mar 1 00:00:27.108: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:27.400: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar 1 00:00:27.400: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar 1 00:00:28.402: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
*Mar 1 00:00:28.402: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
*Jan 19 05:08:47.055: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T1
Router>1, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Thu 24-Aug-06 17:56 by dchih
*Jan 19 05:08:47.055: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Jan 19 05:08:47.087: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down
*Jan 19 05:08:47.091: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname r1-uppe
r1-uppe(config)#^Z
r1-uppe#
r1-uppe#wr
Building configuration...
*Jan 19 05:09:05.834: %SYS-5-CONFIG_I: Configured from console by console[OK]
r1-uppe#
r1-uppe#
r1-uppe#show vers
r1-uppe#show version | i 12.
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T11, RELEASE SOFTWARE (fc3)
ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-advipservicesk9-mz.123-11.T11.bin"
Cisco 2611XM (MPC860P) processor (revision 0x401) with 124858K/6214K bytes of memory.
Processor board ID FTX1121A219 (2454220871)
r1-uppe#
r1-uppe#show contr
r1-uppe#show controllers ds
r1-uppe#show controllers dsL
DSL 0/0 controller DOWN
SLOT 0: Globespan xDSL controller chipset
No frame mode configured
Line Re-activated 0 times after system bootup
LOSW Defect alarm: ACTIVE
CRC per second alarm: ACTIVE
Line termination: CPE
FPGA Revision: 0xA9
Current 15 min CRC: 0
Current 15 min LOSW Defect: 0
Current 15 min ES: 0
Current 15 min SES: 0
Current 15 min UAS: 0
Previous 15 min CRC: 0
Previous 15 min LOSW Defect: 0
Previous 15 min ES: 0
Previous 15 min SES: 0
Previous 15 min UAS: 0
Line-0 status
Chipset Version: 1
Firmware Version: A29733
Modem Status: un checked mode, Status F5B9
Last Fail Mode: No Failure status:0x0
Dying Gasp: Present
r1-uppe#
r1-uppe#
r1-uppe# show ver | i 12.
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T11, RELEASE SOFTWARE (fc3)
ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-advipservicesk9-mz.123-11.T11.bin"
Cisco 2611XM (MPC860P) processor (revision 0x401) with 124858K/6214K bytes of memory.
Processor board ID FTX1121A219 (2454220871)
r1-uppe#
r1-uppe#controller DSL 0/3/0
^
% Invalid input detected at '^' marker.
r1-uppe# mode atm
^
% Invalid input detected at '^' marker.
r1-uppe#! Change to CPE on other end
r1-uppe# line-term co
^
% Invalid input detected at '^' marker.
r1-uppe# dsl-mode shdsl symmetric annex A
^
% Invalid input detected at '^' marker.
r1-uppe# line-rate auto
^
% Invalid input detected at '^' marker.
r1-uppe#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r1-uppe(config)#controller DSL 0/3/0
^
% Invalid input detected at '^' marker.
r1-uppe(config)# mode atm
^
% Invalid input detected at '^' marker.
r1-uppe(config)#! Change to CPE on other end
r1-uppe(config)# line-term co
^
% Invalid input detected at '^' marker.
r1-uppe(config)# dsl-mode shdsl symmetric annex A
^
% Invalid input detected at '^' marker.
r1-uppe(config)# line-rate auto
^
% Invalid input detected at '^' marker.
r1-uppe(config)#controller DSL 0/2
^
% Invalid input detected at '^' marker.
r1-uppe(config)#do show run
Building configuration...
Current configuration : 768 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname r1-uppe
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
!
ip ips po max-events 100
no ftp-server write-enable
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
controller DSL 0/0
line-term cpe
!
controller E1 1/0
!
r1-uppe(config)#controller DSL 0/0
r1-uppe(config-controller)# mode atm
r1-uppe(config-controller)# dsl-mode shdsl symmetric annex A
*Jan 19 05:16:29.120: %CONTROLLER-5-UPDOWN: Contro line-term co
r1-uppe(config-controller)#controller DSL 0/0
*Jan 19 05:16:35.911: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, cha dsl-mode shdsl symmetric annex A
r1-uppe(config-controller)# mode atm
*Jan 19 05:16:41.024: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed st line-rate auto r1-uppe(config-controller)#
r1-uppe(config-controller)#
*Jan 19 05:16:51.249: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
r1-uppe(config-controller)#^Z
r1-uppe#
r1-uppe#
*Jan 19 05:16:54.991: %SYS-5-CONFIG_I: Configured from console by console
r1-uppe#
R2-Nere#
R2-Nere#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2-Nere(config)#controller DSL 0/3/0
^
% Invalid input detected at '^' marker.
R2-Nere(config)# mode atm
^
% Invalid input detected at '^' marker.
R2-Nere(config)#! Change to CPE on other end
R2-Nere(config)# line-term co
^
% Invalid input detected at '^' marker.
R2-Nere(config)# dsl-mode shdsl symmetric annex A
^
% Invalid input detected at '^' marker.
R2-Nere(config)# line-rate auto
^
% Invalid input detected at '^' marker.
R2-Nere(config)#interf dsl 0/0
^
% Invalid input detected at '^' marker.
R2-Nere(config)#do show run
Building configuration...
Current configuration : 753 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2-Nere
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
memory-size iomem 10
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
!
!
!
!
!
controller DSL 0/2
line-term cpe
!
!
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
no fair-queue
!
interface FastEthernet0/1
no ip address
R2-Nere(config)#interf dsl 0/2
^
% Invalid input detected at '^' marker.
R2-Nere(config)#contr dsl 0/2
R2-Nere(config-controller)# mode atm
R2-Nere(config-controller)#contr dsl 0/2
*Dec 16 03:26:35.571: DSL 0/2 gsi_shdsl_set_frame_mode(): mode change
*Dec 16 03:26:36.135: DSL 0/2 gsi_shdsl_set_frame_mode(): mode change
*Dec 16 03:26:36.163: DSL 0/2 xdsl_mode_commandDownload indication
*Dec 16 03:26:36.167: DSL 0/2 process_get_wakeup
*Dec 16 03:26:36.167: DSL 0/2 xdsl_background_process:Download boolean event received
*Dec 16 03:26:36.167: DSL 0/2 xdsl_controller_reset: cdb-state=down
*Dec 16 03:26:36.167: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, changed interf dsl 0/2
*Dec 16 03:26:36.167: DSL 0/2 gsi_shdsl_reset()
*Dec 16 03:26:36.167: DSL 0/2 xdsl_gsi_int_disable(true):: 0x0
*Dec 16 03:26:36.171: DSL 0/2 xcvr_ptr=825577F0
*Dec 16 03:26:36.275: DSL 0/2 Func:gsi_shdsl_shutdown, Line184fail to abort for shutdown
*Dec 16 03:26:36.319: DSL 0/2 SHDSL Line activation started, please wait
*Dec 16 03:26:36.319: DSL 0/2 DSP interrupt enabled
*Dec 16 03:26:36.319: DSL 0/2 Framer interrupt disabled
*Dec 16 03:26:36.319: DSL 0/2
*Dec 16 03:26:36.319: Setting GTI_NTR_LOCAL_OSC
*Dec 16 03:26:36.323: DSL 0/2 xdsl_gsi_int_disable(false):: 0x1
*Dec 16 03:26:36.387: DSL 0/2 dsp interrupt-download next block for line-0
*Dec 16 03:26:36.411: DSL 0/2 framer intr_status 0xC0
*Dec 16 03:26:36.511: DSL 0/2 dsp interrupt-download next block for line-0
*Dec 16 03:26:36.519: DSL 0/2 framer intr_status 0xC0
*Dec 16 03:26:37.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:38.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:39.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:40.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:41.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:42.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:43.323: DSL 0/2 process_get_wakeup^Z ^
% Invalid input detected at '^' marker.
R2-Nere#u
*Dec 16 03:26:43.643: %SYS-5-CONFIG_I: Configured from console by consolen all
All possible debugging has been turned off
R2-Nere#
*Dec 16 03:26:44.323: DSL 0/2 process_get_wakeupconf t
Enter configuration commands, one per line. End with CNTL/Z.
R2-Nere(config)# line-term cpe
^
% Invalid input detected at '^' marker.
R2-Nere(config)# line-
R2-Nere(config)# line?
line
R2-Nere(config)# line ?
<0-70> First Line number
aux Auxiliary line
console Primary terminal line
tty Terminal controller
vty Virtual terminal
x/y Slot/Port for Modems
R2-Nere(config)#control
R2-Nere(config)#controll
R2-Nere(config)#controller ds
R2-Nere(config)#controller dsL 0/2
R2-Nere(config)#controller dsL 0/2
R2-Nere(config-controller)# line-term cpe
R2-Nere(config-controller)# dsl-mode shdsl symmetric annex A
R2-Nere(config-controller)#controller dsL 0/2
*Dec 16 03:27:23.067: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, chainterf dsl 0/2
R2-Nere(config-controller)# line-rate auto
R2-Nere(config-controller)#
*Dec 16 03:27:38.211: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, changed state to down^Z
R2-Nere#
R2-Nere#
R2-Nere#sh
*Dec 16 03:27:39.475: %SYS-5-CONFIG_I: Configured from console by consoleow run | se DSL
controller DSL 0/2
mode atm
line-term cpe
line-mode 2-wire line-zero
dsl-mode shdsl symmetric annex A
line-rate auto
R2-Nere#
r1-uppe#show run | se DSL
controller DSL 0/0
mode atm
line-term co
line-mode 2-wire line-zero
dsl-mode shdsl symmetric annex A
line-rate auto
r1-uppe#
r1-uppe#debug xdsl
r1-uppe#debug xdsl ?
application xDSL application
driver xDSL driver
eoc xDSL eoc
error xDSL error
r1-uppe#debug xdsl error
xDSL error debugging is on
r1-uppe#debug xdsl dri
r1-uppe#debug xdsl driver
xDSL driver debugging is on
r1-uppe#debug xdsl app
xDSL application debugging is on
r1-uppe#
*Jan 19 05:20:07.863: DSL 0/0 process_get_wakeup
*Jan 19 05:20:08.865: DSL 0/0 process_get_wakeup
*Jan 19 05:20:09.866: DSL 0/0 process_get_wakeup
*Jan 19 05:20:10.868: DSL 0/0 process_get_wakeupdebug xdsl app
*Jan 19 05:20:11.869: DSL 0/0 process_get_wakeup
*Jan 19 05:20:12.871: DSL 0/0 process_get_wakeupno debug xdsl app
xDSL application debugging is off
r1-uppe#
*Jan 19 05:20:13.873: DSL 0/0 process_get_wakeupno debug xdsl error
xDSL error debugging is off
r1-uppe#
r1-uppe#
r1-uppe#
r1-uppe#debug xdsl error
xDSL error debugging is on
r1-uppe#
*Jan 19 05:21:22.629: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:22.637: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:28.030: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:28.038: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:33.467: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:33.491: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:33.567: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:33.587: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:33.688: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:33.696: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:36.484: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:36.488: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:36.785: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:36.801: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:37.157: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:37.169: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:39.798: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:39.802: DSL 0/0 framer intr_status 0xC0
r1-uppe# line-rate auto
*Jan 19 05:21:53.260: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:53.264: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:53.704: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:53.712: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:53.905: DSL 0/0 dsp interrupt-download next block for line-0
*Jan 19 05:21:53.909: DSL 0/0 DSP interrupt disabled
*Jan 19 05:21:53.909: DSL 0/0 Download completed for line-0
*Jan 19 05:21:53.913: DSL 0/0 Framer interrupt enabled
*Jan 19 05:21:53.913: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:53.913: DSL 0/0 controller Link up! line rate: 2304 Kbps
'''*Jan 19 05:21:53.917: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to up'''
*Jan 19 05:21:54.017: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:54.017: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.021: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.113: DSL 0/0 framer intr_status 0xC1
*Jan 1conf tSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.113: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.133: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.133: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.133: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.209: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:54.209: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.209: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.225: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.229: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.229: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.305: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:54.305: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.305: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.321: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.325: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.325: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.418: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.422: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.422: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.514: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.518: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.518: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.522: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.522: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.522: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.009: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:59.009: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.009: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.013: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.017: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.017: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.021: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.021: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.021: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.105: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:59.105: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.105: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.121: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.125: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.125: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.201: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:59.201: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.201: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.217: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.221: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.221: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.298: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:59.298: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.298: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.314: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.318: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.318: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.322: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.322: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.322: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1un all
^
% Invalid input detected at '^' marker.
r1-uppe#
*Jan 19 05:22:04.005: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.009: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.009: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.013: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:04.013: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.013: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.013: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.109: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:04.109: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.109: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.125: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.129: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.129: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.206: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:04.206: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.206: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.222: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.226: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.226: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.302: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:04.302: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.302: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.318: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.322: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.322: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.326: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.326: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.326: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1^Z
r1-uppe#un all
All possible debugging has been turned off
r1-uppe#
*Jan 19 05:22:09.005: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:09.005: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:09.005: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:09.009: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:09.014: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:09.014: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:09.018: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:09.018: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:09.018: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:09.102: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:09.102: DSL 0/0 xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:09.102: DSL 0/0 xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:09.118: DSL 0/0 framer intr_status 0xC4
r1-uppe#
r1-uppe#show ip interf bri
Interface IP-Address OK? Method Status Protocol
ATM0/0 unassigned YES unset initializing down
FastEthernet0/0 unassigned YES unset administratively down down
FastEthernet0/1 unassigned YES unset administratively down down
r1-uppe#
r1-uppe#
*Jan 19 05:22:20.396: %LINK-3-UPDOWN: Interface ATM0/0, changed state to up
*Jan 19 05:22:21.398: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to up
r1-uppe#
r1-uppe#
r1-uppe#show ip interf bri
Interface IP-Address OK? Method Status Protocol
'''ATM0/0 unassigned YES unset up up'''
FastEthernet0/0 unassigned YES unset administratively down down
FastEthernet0/1 unassigned YES unset administratively down down
r1-uppe#
r1-uppe#
r1-uppe#show atm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts
r1-uppe#
r1-uppe#show run | sec ATM
interface ATM0/0
no ip address
no atm ilmi-keepalive
r1-uppe#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r1-uppe(config)#interf atm 0/0
r1-uppe(config-if)#no ip address
r1-uppe(config-if)# load-interval 30
r1-uppe(config-if)# no atm ilmi-keepalive
r1-uppe(config-if)# clock rate aal5 8000000
^
% Invalid input detected at '^' marker.
r1-uppe(config-if)# clock rate aal5 ?
1000000
1300000
1600000
2000000
2600000 (default)
3200000
4000000
5300000
7000000
<1000000-7000000> clock rates in bits per second, choose one from above
r1-uppe(config-if)# clock rate aal5 7000000
%ATM0/0 Resetting interface...
r1-uppe(config-if)#
*Jan 19 05:25:37.235: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
*Jan 19 05:25:37.752: %LINK-3-UPDOWN: Interface ATM0/0, changed state to down
*Jan 19 05:25:38.753: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to down
r1-uppe(config-if)#no clock rate aal5 7000000
%Defaulting to 2600000 bps
%ATM0/0: Bringing interface up...
r1-uppe(config-if)#
*Jan 19 05:25:54.752: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
r1-uppe(config-if)#
r1-uppe(config-if)#show ip interf bri
^
% Invalid input detected at '^' marker.
r1-uppe(config-if)#do show ip interf bri
Interface IP-Address OK? Method Status Protocol
ATM0/0 unassigned YES manual down down
FastEthernet0/0 unassigned YES unset administratively down down
FastEthernet0/1 unassigned YES unset administratively down down
r1-uppe(config-if)#
r1-uppe(config-if)#show atm vc
^
% Invalid input detected at '^' marker.
r1-uppe(config-if)#do show atm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts
r1-uppe(config-if)#do show run | sec ATM
interface ATM0/0
no ip address
load-interval 30
no atm ilmi-keepalive
r1-uppe(config-if)#
*Jan 19 05:27:02.142: DSL 0/0 controller Link up! line rate: 2304 Kbps
*Jan 19 05:27:02.142: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to up
r1-uppe(config-if)#
r1-uppe(config-if)#interf atm
*Jan 19 05:27:30.408: %LINK-3-UPDOWN: Interface ATM0/0, changed state to up
*Jan 19 05:27:31.410: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to up0/0
r1-uppe(config-if)#interf atm 0/0.1 po
r1-uppe(config-if)#interf atm 0/0.1 poi
r1-uppe(config-if)#interf atm 0/0.1 point-to-point
r1-uppe(config-subif)#ip address 1.1.1.1 255.255.255.0
r1-uppe(config-subif)#pvc 2/100
r1-uppe(config-if-atm-vc)# vbr-rt 2000 2000
r1-uppe(config-if-atm-vc)# oam-pvc 0
r1-uppe(config-if-atm-vc)# encapsulation aal5mux ip
r1-uppe(config-if-atm-vc)#^Z
r1-uppe#
r1-uppe#
*Jan 19 05:28:37.839: %ATM-5-UPDOWN: Interface ATM0/0.1, Changing autovc 2/100 to PVC activated.
*Jan 19 05:28:37.839: %ATM-5-UPDOWN: Interface ATM0/0.1, Changing autovc 2/100 to PVC created.
*Jan 19 05:28:37.839: %SYS-5-CONFIG_I: Configured from console by console
r1-uppe#show atm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts
0/0.1 1 2 100 PVC MUX VBR 2000 2000 0 UP
r1-uppe#
R2-Nere>ena
R2-Nere#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2-Nere(config)#
r1-uppe#show running | sec ATM
interface ATM0/0
no ip address
load-interval 30
no atm ilmi-keepalive
interface ATM0/0.1 point-to-point
ip address 1.1.1.1 255.255.255.0
pvc 2/100
vbr-rt 2000 2000
oam-pvc 0
encapsulation aal5mux ip
!
r1-uppe#
R2-Nere(config)#interf atm 0/2
R2-Nere(config-if)# load-interval 30
R2-Nere(config-if)# no atm ilmi-keepalive
R2-Nere(config-if)#exit
R2-Nere(config)#interf atm 0/2.1 point
R2-Nere(config)#interf atm 0/2.1 point-to-point
R2-Nere(config-subif)#ip address 1.1.1.2 255.255.255.0
R2-Nere(config-subif)# pvc 2/100
R2-Nere(config-if-atm-vc)# vbr-rt 2000 2000
R2-Nere(config-if-atm-vc)# oam-pvc 0
R2-Nere(config-if-atm-vc)# encapsulation aal5mux ip
R2-Nere(config-if-atm-vc)#^Z
R2-Nere#
R2-Nere#
*Dec 16 03:39:25.327: %SYS-5-CONFIG_I: Configured from console by console
R2-Nere#show atm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts
0/2.1 1 2 100 PVC MUX VBR 2000 2000 0 UP
R2-Nere#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms
R2-Nere#show atm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts
0/2.1 1 2 100 PVC MUX VBR 2000 2000 0 UP
R2-Nere#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2-Nere(config)#line vty 0 15
R2-Nere(config-line)#login
% Login disabled on line 66, until 'password' is set
% Login disabled on line 67, until 'password' is set
% Login disabled on line 68, until 'password' is set
% Login disabled on line 69, until 'password' is set
% Login disabled on line 70, until 'password' is set
% Login disabled on line 71, until 'password' is set
% Login disabled on line 72, until 'password' is set
% Login disabled on line 73, until 'password' is set
% Login disabled on line 74, until 'password' is set
% Login disabled on line 75, until 'password' is set
% Login disabled on line 76, until 'password' is set
% Login disabled on line 77, until 'password' is set
% Login disabled on line 78, until 'password' is set
% Login disabled on line 79, until 'password' is set
% Login disabled on line 80, until 'password' is set
% Login disabled on line 81, until 'password' is set
R2-Nere(config-line)#passw
R2-Nere(config-line)#password cisco
R2-Nere(config-line)#
R2-Nere(config-line)#
R2-Nere(config-line)#^Z
R2-Nere#
R2-Nere#
*Dec 16 03:40:12.839: %SYS-5-CONFIG_I: Configured from console by console
r1-uppe#show ip interf bri
Interface IP-Address OK? Method Status Protocol
ATM0/0 unassigned YES manual up up
ATM0/0.1 1.1.1.1 YES manual up up
FastEthernet0/0 unassigned YES unset administratively down down
FastEthernet0/1 unassigned YES unset administratively down down
r1-uppe#1.1.1.2
Trying 1.1.1.2 ... Open
User Access Verification
Password:
R2-Nere>exit
[Connection to 1.1.1.2 closed by foreign host]
r1-uppe#
r1-uppe#show atm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts
0/0.1 1 2 100 PVC MUX VBR 2000 2000 0 UP
r1-uppe#
r1-uppe#
