DSL-cards
From Datateknik
(Difference between revisions)
(→Experiments with DSL cards) |
(→Documentation) |
||
| Line 3: | Line 3: | ||
== Documentation == | == Documentation == | ||
* Pinout ? [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/ic/hardware/installation/guide/dsl_hwic.html#wp1062129 table 2, table 3] | * Pinout ? [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/ic/hardware/installation/guide/dsl_hwic.html#wp1062129 table 2, table 3] | ||
| + | * LED description [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/ic/hardware/installation/guide/dsl_hwic.html#wp1061505 table 5] | ||
| + | *: LP off, | ||
| + | *: CD Green when cells or frames are passing between the host and the DSLAM, | ||
| + | *: OK green | ||
* WIC-1SHDSL and WIC-1SHDSL-V2 [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/roadmaps/wicshdsl.html '''Documentation Roadmap''' ] | * WIC-1SHDSL and WIC-1SHDSL-V2 [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/roadmaps/wicshdsl.html '''Documentation Roadmap''' ] | ||
* [http://www.cisco.com/c/en/us/support/docs/long-reach-ethernet-lre-digital-subscriber-line-xdsl/symmetrical-high-data-rate-dsl-gshdsl/25900-dsl-cpe-config.html Configuring CPE '''Back-to-Back''' Through G.SHDSL Ports] | * [http://www.cisco.com/c/en/us/support/docs/long-reach-ethernet-lre-digital-subscriber-line-xdsl/symmetrical-high-data-rate-dsl-gshdsl/25900-dsl-cpe-config.html Configuring CPE '''Back-to-Back''' Through G.SHDSL Ports] | ||
Revision as of 14:28, 24 March 2014
Contents |
Experiments with DSL cards
Documentation
- Pinout ? table 2, table 3
- LED description table 5
- LP off,
- CD Green when cells or frames are passing between the host and the DSLAM,
- OK green
- WIC-1SHDSL and WIC-1SHDSL-V2 Documentation Roadmap
- Configuring CPE Back-to-Back Through G.SHDSL Ports
- Configuring PPP over ATM with NAT
is it there ??
During boot
Self decompressing the image : ######################################################################################### ########################################################################################### ########################################################################################### ####################################################################### [OK] IOMEM set to: 5 Unknown Card in slot 0 PMem allocated: 381681664 bytes; IOMem allocated: 20971520 bytes ... ... Cisco 2801 (revision 7.0) with 372736K/20480K bytes of memory. Processor board ID FCZ112070FT 1 DSL controller 2 FastEthernet interfaces 2 Serial(sync/async) interfaces 1 Virtual Private Network (VPN) Module DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 62720K bytes of ATA CompactFlash (Read/Write)
Commands:
show diag
WIC/VIC/HWIC Slot 3:
GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
Hardware Revision : 0.0
Top Assy. Part Number : 800-23445-01
Board Revision : C0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC08170N9M
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier :
Product (FRU) Number :
EEPROM format version 4
show running ! controller DSL 0/3/0 !
R1(config)#controller dsl 0/3/0
R1(config-controller)#?
Controller configuration commands:
default Set a command to its defaults
description Controller specific description
dsl-mode SHDSL mode
exit Exit from controller configuration mode
help Description of the interactive help system
ignore-error-duration Number of seconds errors such as CRC are ignored while
the line is training (default is 0)
line-term Customer Premise or Central Office
loopback XDSL loopback test
mode Configure the xdsl controller mode
no Negate a command or set its defaults
shutdown Shutdown the xdsl controller
snr SNR
R1(config-controller)#
How to do it
- make the DSL-controller create the ATM interface
- controller DSL 0/3/0
- mode atm
- line-term co
- dsl-mode shdsl symmetric annex A
- line-rate auto
- Configure the ATM interface
- interface ATRM 0/3/0
- no ip address
- no atm ilmi-keepalive
- !
- pvc 0/35
- encapsulation aal5snap
- !
- pvc 8/35
- encapsulation aal5mux ppp dialer
- dialer pool-member 1
- Create interface Dialer0
- interface Dialer0
- ip address 1.1.1.1 255.255.255.0
- encapsulation ppp
- dialer pool 1
- dialer-group 1
- Create dialer-list
- dialer-list 1 protocol ip permit
Debugging: clear
- clear interface atm 0/3/0
show
- show atm vc
- show dsl interface atm 0/3/0
- show controller DSL 0/3/0
- show interfaces atm 0/3/0
debug
- debug atm events
- debug atm errors
???
- dslsar disable ATM0/3/0
- dslsar enable ATM0/3/0
