DSL-cards

From Datateknik
(Difference between revisions)
Jump to: navigation, search
(→‎Experiments with DSL cards)
(→‎Documentation)
 
(67 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
= Experiments with DSL cards =
 
= Experiments with DSL cards =
−
* WIC-1SHDSL and WIC-1SHDSL-V2 [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/roadmaps/wicshdsl.html '''Documentation Roadmap''' ]
+
{| class="wikitable"
−
* [http://www.cisco.com/c/en/us/support/docs/long-reach-ethernet-lre-digital-subscriber-line-xdsl/symmetrical-high-data-rate-dsl-gshdsl/25900-dsl-cpe-config.html Configuring CPE '''Back-to-Back''' Through G.SHDSL Ports]
+
|-
 +
! HWIC-4SHDSL
 +
!  
 +
! WIC-1SHDSL-V2
 +
|-
 +
| [[File:HWIC-4SHDSL.jpg|320px|HWIC 4SHDSL -- Card in 2600-routers]]
 +
|  
 +
| [[File:WIC-1SHDSL-V2.jpg|320px|WIC-1SHDSL-V2 -- Card in 2600-routers]]
 +
|-
 +
| Card in 2900 routers (8pin pink RJ45 port)
 +
|  
 +
| Card in old 2600 routers (6pin pink RJ12 port)
 +
|}
 +
 
 +
 
 +
 
 
== Documentation ==
 
== Documentation ==
 +
* <font colror="red">[[https://www.viavisolutions.com/en-us/literature/xdsl-poster-poster-chart-en.pdf xDSL Poster]]
 +
* [http://www.cisco.com/c/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/prod_white_paper0900aecd80645923.html QoS in ADSL] using TGN (Pagent)
 +
* Supported IOS versions for HWIC-2SHDSL-v2, [http://www.cisco.com/c/en/us/products/collateral/routers/3600-series-multiservice-platforms/product_data_sheet09186a00800921f0.html?mdfid=279042640 HWIC-2SHDSL-v3 Table 7. Minimum Cisco IOS Software Release Required for New WICs]
 +
* Pinout RJ11-RJ11 [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/ic/hardware/installation/guide/dsl_hwic.html#wp1062129 table 2, table 3], RJ45 to RJ11 [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/ic/hardware/installation/guide/dsl_hwic.html#wp1054781 table 13,14]
 +
* LED description [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/ic/hardware/installation/guide/dsl_hwic.html#wp1061505 table 5]
 +
*: LP off,
 +
*: CD Green when cells or frames are passing between the host and the DSLAM,
 +
*: OK green
 +
* WIC-1SHDSL and WIC-1SHDSL-V2 [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/roadmaps/wicshdsl.html '''Documentation Roadmap''' ]
 +
* BAD: [http://www.cisco.com/c/en/us/support/docs/long-reach-ethernet-lre-digital-subscriber-line-xdsl/symmetrical-high-data-rate-dsl-gshdsl/25900-dsl-cpe-config.html Configuring CPE '''Back-to-Back''' Through G.SHDSL Ports]
 +
* GOOD: [http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/15-mt/ir-15-mt-book/bba-atm-shdsl.html ATM Mode for Two-Wire or Four-Wire SHDSL] incl. Back-to-Back
 +
* [http://www.cisco.com/c/en/us/td/docs/routers/access/1800/1801/software/configuration/guide/scg/pppoanat.html#22040 Configuring PPP over ATM with NAT]
 +
* FRAMTIDEN: [http://www.2mul.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/15-mt/ir-15-mt-book.pdf Broadband Access -- How To Do It]
 +
* NYA KORTET: HWIC-2SHDSL [http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/software/feature/guide/shdslfm.html Configuring]
 +
* [http://www.cisco.com/c/en/us/support/docs/asynchronous-transfer-mode-atm/permanent-virtual-circuits-pvc-switched-virtual-circuits-svc/10480-oam.html Using OAM for PVC Management],
 +
*: [http://www.routerie.com/cgi-bin/ultimatebb.cgi?ubb=print_topic;f=50;t=002730 How to use "encap aal5ciscoppp virtual-temp 1"]
 +
*: [http://www.iec.net/mp08h-pi-10.html pink sleeves] [file:http://www.cable-trader.co.uk/images/items/strain_relief_boot_pink.jpg]
 +
 +
== Laboration ==
 +
Laboration
 +
# Configure Hostnames "Router2900" and "Router2600" to your routers !
 +
# Figure out which slot your DSL card is in by using the commands:
 +
#: <pre>Router2900#show controller shdsl</pre>
 +
#: <pre>Router2600#show controller dsl</pre>
 +
#: Answers: 2900-Slot _____________ and 2600-Slot _____________
 +
# Try the commands <pre>show running</pre> and find all lines that include '''controller''' and '''dsl''' on both routers
 +
#: Answer: 2600 ________________
 +
#: Answer: 2900 ________________
 +
# What is the difference between <tt> '''interface serial 0/0''' </tt> and <tt> '''controller serial 0/0''' </tt> ?
 +
# How many ATM interfaces exists in '''show running'''
 +
#: Answer: ______________
 +
=== 2900 SETUP ===
 +
# Configure the DSL controller of the 2900
 +
#: <tt>controller SHDSL 0/3/0</tt>
 +
#:  <tt> &nbsp; description This is the CPE</tt>
 +
#:  <tt> &nbsp; ! <font color=red>Automatically assign the Central Office (CO) configuration to </font> </tt>
 +
#:  <tt> &nbsp; ! <font color=red>an ATM dsl-group on the Customer Premise Equipment (CPE). </font> </tt>
 +
#:  <tt> &nbsp; dsl-group auto</tt>
 +
DIDN'T WORK, PLEASE USE
 +
controller SHDSL 0/3/0
 +
  description Can *only* run in CPE mode
 +
  dsl-group 0 pairs  0, 1
 +
    shdsl 4-wire mode enhanced
 +
    shdsl annex A
 +
    shdsl rate 4096
 +
  !
 +
 +
# How many ATM interfaces exists in '''show running'''
 +
#: Answer: ______________
 +
# Configure the ATM interface of the 2900
 +
#: <tt>interface ATM 0/3/0  </tt>                           
 +
#:  <tt> &nbsp; no ip address      </tt>   
 +
#:  <tt> &nbsp; load-interval 30  </tt>   
 +
#:  <tt> &nbsp; no atm ilmi-keepalive  </tt>   
 +
#Try the command '''show ip interface brief'''
 +
#Create a ATM subinterface with a Layer2 VPI/VCI and a Layer3 IP-address
 +
#: <tt>  interface ATM 0/3/0.1 point-to-point </tt>   
 +
#:  <tt> &nbsp;  description Connection to Router2600 (Central Office) </tt>   
 +
#:  <tt> &nbsp;  ip address 1.1.1.2 255.255.255.0</tt>   
 +
#:  <tt> &nbsp;  pvc 2/100 </tt>   
 +
#:  <tt> &nbsp; &nbsp;    vbr-rt 2000 2000</tt>   
 +
#:  <tt> &nbsp; &nbsp;    oam-pvc manage auto-detect</tt>   
 +
#: <tt>  &nbsp; &nbsp;    encapsulation aal5mux ip</tt>   
 +
#Try the command '''show ip interface brief'''
 +
 +
=== 2600 SETUP ===
 +
# How many ATM interfaces exists in '''show running'''
 +
#: Answer: ______________
 +
# Try the command '''show ip interface brief'''
 +
# Configure the DSL controller of the 2600
 +
#: <tt>controller DSL 0/2</tt>
 +
#:  <tt>  description This is CO, the other end is CPE</tt>
 +
#:  <tt>  mode atm</tt>
 +
#:  <tt>  line-term co</tt>
 +
#:  <tt>  line-mode 4-wire</tt>
 +
#:  <tt>  dsl-mode shdsl symmetric annex A</tt>
 +
#:  <tt>  line-rate 4096</tt>
 +
# How many ATM interfaces exists in '''show running'''
 +
#: Answer: ______________
 +
# Configure the ATM interface of the 2600
 +
#: <tt>interface ATM 0/2  </tt>
 +
#:  <tt>  description ATM over DSL (Central Office)    </tt> 
 +
#:  <tt>  no ip address      </tt>   
 +
#:  <tt>  load-interval 30  </tt>   
 +
#:  <tt>  no atm ilmi-keepalive  </tt>   
 +
#Try the command '''show ip interface brief'''
 +
#Create a ATM subinterface with a Layer2 VPI/VCI and a Layer3 IP-address
 +
#: <tt>  interface ATM 0/2.1 point-to-point </tt>   
 +
#:  <tt>  &nbsp;  description Connection to Router2900 (Customer) </tt>   
 +
#:  <tt>  &nbsp;  ip address 1.1.1.1 255.255.255.0</tt>   
 +
#:  <tt>  &nbsp;  pvc 2/100 </tt>   
 +
#:  <tt>  &nbsp; &nbsp;    vbr-rt 2000 2000</tt>   
 +
#:  <tt>  &nbsp; &nbsp;    no oam-pvc manage</tt>   
 +
#:  <tt>  &nbsp; &nbsp;    encapsulation aal5mux ip</tt>   
 +
#Try the command '''show ip interface brief'''
 +
#: You might get:
 +
#:  <tt>  ATM0/2            unassigned      YES manual initializing          down</tt>
 +
#:  <tt>  ATM0/2.1          1.1.1.1        YES manual initializing          down</tt>
 +
# Let's ping the other end !!
 +
# Ûberkurz:
 +
## What show-command shows the line-speed of the xDSL controller
 +
## What show-command shows if the controller is running as CPE or CO
 +
## What ATM AAL options are available on both cards?
 +
##: Are there any special PPP settings that are required to make communication work? Try!
 +
## What is the theory behind the PVC's?
 +
##: Are there any special control PVC's (like 0/32 ?!?) ?
 +
 +
== MINIMAL 29/4 ==
 +
Router2600#show running | sec ATM|DSL
 +
controller DSL 0/2
 +
  description This is CO, the other end is CPE
 +
  mode atm
 +
  line-term co
 +
  line-mode 2-wire line-zero
 +
  dsl-mode shdsl symmetric annex B
 +
  line-rate 2048
 +
interface ATM0/2.1 point-to-point
 +
  ip address 1.1.1.1 255.255.255.0
 +
  ipv6 address 2001::1/64
 +
  cdp enable
 +
pvc 2/100
 +
  encapsulation aal5snap
 +
!
 +
 +
Router2900#show run | sec DSL|ATM
 +
controller SHDSL 0/3/0
 +
  description Can *only* run in CPE mode
 +
  dsl-group auto
 +
interface ATM0/3/0.1 point-to-point
 +
  ip address 1.1.1.2 255.255.255.0
 +
  ipv6 address 2001::2/64
 +
  cdp enable
 +
  pvc 2/100
 +
    encapsulation aal5snap
 +
!
 +
 +
== How to do it ==
 +
! On 2801 running IOS  (C2801-ADVIPSERVICESK9-M), Version '''12.4(24)T'''
 +
! #show controller dsl | inc Firmware|prog
 +
!  Firmware Version:  '''R4.2.1'''
 +
!
 +
 +
! <font color=red>'''Fungerar INTE'''</font>
 +
!  2801 Software (C2801-ADVIPSERVICESK9-M), Version 15.1(4)M6
 +
! show controll DSL | i Firm|prog
 +
!  Firmware Version:  388.132
 +
!  '''DSL firmware download in progress, please wait'''
 +
 +
 +
! make the DSL-controller create the ATM interface
 +
  controller DSL 0/3/0                                  controller SHDSL 0/3/0
 +
    mode atm                                              dsl-group auto
 +
! <font color=red>Change to CPE on other end</font>
 +
    line-term co                                         
 +
  line-mode 2-wire line-zero
 +
  dsl-mode shdsl symmetric annex A                        shdsl annex A
 +
  line-rate auto                                          !shdsl rate -- Only on CO side !!
 +
 +
! Configure the ATM interface
 +
interface ATM 0/3/0                              <-- SAME for 2901 gh.shDSL
 +
  no ip address
 +
  load-interval 30
 +
  no atm ilmi-keepalive
 +
!
 +
interface ATM 0/3/0.1 point-to-point
 +
  ! <font color=red>Change to .2 on other end</font>
 +
  ip address 1.1.1.1 255.255.255.0
 +
  pvc 2/100
 +
    vbr-rt 2000 2000
 +
    oam-pvc 0
 +
    encapsulation aal5mux ip
 +
 +
show atm vc
 +
            VCD /                                        Peak  Avg/Min Burst
 +
Interface  Name        VPI  VCI  Type  Encaps  SC  Kbps  Kbps  Cells  Sts
 +
0/0.1      1              2  100  PVC    MUX      VBR    2000  2000    0  UP
 +
 +
 +
'''Minimal Setup'''
 +
controller DSL 0/3/0
 +
  mode atm
 +
  line-term co
 +
interface ATM0/3/0.1 point-to-point
 +
  ip address 1.1.1.1 255.255.255.0
 +
  pvc 2/100
 +
    encapsulation aal5mux ip
 +
 +
== Todays Errors ==
 +
 +
 +
  Hi,
 +
to force CO mode you need to configure 'termination CO' under the controller SHDSL.
 +
  However, only HWIC-4SHDSL supports that command. See here for reference:
 +
  "Q. Do the G.SHDSL HWICs work in central-office mode (back-to-back connection without a DSLAM)?
 +
  A. Currently only the HWIC-4SHDSL supports both CPE and central-office  modes for diagnostic purposes. The mode of operation can be set only  from the ROM Monitor environment. CPE is the default mode of operation."
 +
[http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps7175/prod_qas0900aecd80591ff1.html
 +
  http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps7175/prod_qas0900aecd80591ff1.html]
 +
 
 +
Hope this helps
 +
  Marco
 +
 +
 +
  Router#show diag
 +
  Slot 0:
 +
        '''C2610''' 1E Mainboard Port adapter, 4 ports
 +
  ...
 +
  WIC Slot 1:
 +
        <font color=red>Unknown WAN daughter card</font>
 +
        ...
 +
        Product Number          : WIC-1SHDSL-V2
 +
Router#show vers | inc 12
 +
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(8)T5,  RELEASE SOFTWARE (fc1)
 +
System image file is "flash:c2600-i-mz.122-8.T5.bin"
 +
 +
Router2600#show diag
 +
Slot 0:
 +
        '''C2621''' 2FE Mainboard Port adapter, 5 ports
 +
  ...
 +
        WIC Slot 1:
 +
        <font color=red>Unknown WAN daughter card</font>
 +
 +
Router2600#show vers | inc 12
 +
IOS (tm) C2600 Software (C2600-BIN-M), Version 12.3(25), RELEASE SOFTWARE (fc1)
 +
System image file is "flash:c2600-bin-mz.123-25.bin"
 +
 
 +
  show diag
 +
      WIC Slot 1:
 +
        <font color=green>GSI GSHDSL MULTI LINE ATM/T1/E1 WIC</font>
 +
Router#show vers
 +
  Cisco IOS Software, C2600 Software (C2600-IPBASEK9-M), Version 12.4(17a), RELEASE SOFTWARE (fc2)
 +
  System image file is "flash:c2600-ipbasek9-mz.124-17a.bin"
 +
  Cisco '''2621XM''' (MPC860P) processor (revision 1.0) with 59392K/6144K bytes of memory.
 +
 +
 +
 
 +
 +
  show controller atM 0/3/0
 +
  WIC Config Reg2  0x04      Gen bus error on bad G.SHDSL ATM/T1/E1 access
 +
  ...
 +
  Interface Serial0/3/0
 +
  Hardware is GT96K
 +
  DTE Unknown (13) RX clock detected.
 +
 +
    2901# show diag
 +
        ...
 +
        WIC Slot 3:
 +
        GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
 +
 +
        '''WIC module not supported/disabled in this slot'''
 +
        Hardware Revision        : 0.0
 +
        Top Assy. Part Number    : 800-23445-02
 +
        Board Revision          : A0
 +
        Deviation Number        : 78181
 +
        Fab Version              : 04
 +
        PCB Serial Number        : FOC09132CUJ
 +
        RMA Test History        : 00
 +
        RMA Number              : 0-0-0-0
 +
        RMA History              : 00
 +
        Version Identifier      : V02
 +
        Product (FRU) Number    : WIC-1SHDSL-V2
 +
 
== is it there ?? ==
 
== is it there ?? ==
 
'''During boot'''
 
'''During boot'''
Line 30: Line 306:
 
   WIC/VIC/HWIC Slot 3:
 
   WIC/VIC/HWIC Slot 3:
 
         GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
 
         GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
−
 
+
 
 
         Hardware Revision        : 0.0
 
         Hardware Revision        : 0.0
 
         Top Assy. Part Number    : 800-23445-01
 
         Top Assy. Part Number    : 800-23445-01
Line 48: Line 324:
 
   controller DSL 0/3/0
 
   controller DSL 0/3/0
 
   !
 
   !
 +
 +
R1(config)#controller dsl 0/3/0
 +
R1(config-controller)#?
 +
Controller configuration commands:
 +
  default                Set a command to its defaults
 +
  description            Controller specific description
 +
  dsl-mode              SHDSL mode
 +
  exit                  Exit from controller configuration mode
 +
  help                  Description of the interactive help system
 +
  ignore-error-duration  Number of seconds errors such as CRC are ignored while
 +
                          the line is training (default is 0)
 +
  line-term              Customer Premise or Central Office
 +
  loopback              XDSL loopback test
 +
  mode                  Configure the xdsl controller mode
 +
  no                    Negate a command or set its defaults
 +
  shutdown              Shutdown the xdsl controller
 +
  snr                    SNR
 +
R1(config-controller)#
 +
 +
 +
==Debugging==
 +
'''clear'''
 +
* clear interface atm 0/3/0
 +
'''show'''
 +
* show atm vc
 +
* show dsl interface atm 0/3/0
 +
* R1#show controllers dsl brief
 +
DSL 0/3/0 controller DOWN
 +
Globespan xDSL controller chipset
 +
DSL mode: Not Trained
 +
Frame mode: Utopia
 +
Configured Line rate: 2048Kbps
 +
Line Re-activated 0 times after system bootup
 +
LOSW Defect alarm: ACTIVE
 +
CRC per second alarm: ACTIVE
 +
Line termination: CO
 +
FPGA Revision: 0xB3
 +
* show controller DSL 0/3/0
 +
* show interfaces atm 0/3/0
 +
'''debug'''
 +
* debug atm events
 +
* debug atm errors
 +
* debug xdsl driver
 +
'''???'''
 +
* dslsar disable ATM0/3/0
 +
* dslsar enable ATM0/3/0
 +
== Latest BUG hunt ==
 +
=== show controllers dsl ===
 +
! ON A CISCO 2801
 +
Line-0 status
 +
Chipset Version:  0
 +
Firmware Version:  388.132
 +
Modem Status:  Handshake, Status 10
 +
Last Fail Mode:  No Failure status:0x0
 +
DSL firmware download in progress, please wait
 +
Dying Gasp: Present
 +
 +
! ON A 26x1 XM, IOS  12.4
 +
Line-0 status
 +
Chipset Version:  1
 +
Firmware Version:  A29733
 +
Modem Status:  un checked mode, Status F5B9
 +
Last Fail Mode:  No Failure status:0x0
 +
Dying Gasp: Present
 +
 +
! ON A 2611 XM, IOS  12.3(11)T11
 +
Line-0 status
 +
Chipset Version:  0
 +
Firmware Version:  R3.0.1
 +
Modem Status:  un checked mode, Status DF3D
 +
Last Fail Mode:  No Failure status:0x0
 +
Dying Gasp: Present
 +
 +
== Så här gick det till när det fungerade första gången ==
 +
 +
Router>
 +
Router>ena
 +
Router#conf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
Router(config)#hostname R2-Nere
 +
R2-Nere(config)#^Z
 +
R2-Nere#
 +
R2-Nere#
 +
*Dec 16 03:11:14.075: %SYS-5-CONFIG_I: Configured from console by consolewr
 +
Building configuration...
 +
[OK]
 +
R2-Nere#
 +
R2-Nere#show running
 +
Building configuration...
 +
 +
Current configuration : 753 bytes
 +
!
 +
version 12.4
 +
service timestamps debug datetime msec
 +
service timestamps log datetime msec
 +
no service password-encryption
 +
!
 +
hostname R2-Nere
 +
!
 +
boot-start-marker
 +
boot-end-marker
 +
!
 +
!
 +
no aaa new-model
 +
memory-size iomem 10
 +
no network-clock-participate slot 1
 +
no network-clock-participate wic 0
 +
ip cef
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
controller DSL 0/2
 +
  line-term cpe
 +
!
 +
!
 +
!
 +
interface FastEthernet0/0
 +
  no ip address
 +
  shutdown
 +
  duplex auto
 +
  speed auto
 +
!
 +
interface Serial0/0
 +
  no ip address
 +
  shutdown
 +
  no fair-queue
 +
!
 +
interface FastEthernet0/1
 +
  no ip address
 +
  shutdown
 +
  duplex auto
 +
  speed auto
 +
!
 +
interface Serial0/1
 +
  no ip address
 +
  shutdown
 +
!
 +
ip forward-protocol nd
 +
!
 +
ip http server
 +
no ip http secure-server
 +
!
 +
!
 +
control-plane
 +
!
 +
!
 +
line con 0
 +
line aux 0
 +
line vty 0 4
 +
!
 +
!
 +
end
 +
 +
=== pre ===
 +
<pre>
 +
R2-Nere#debug xds
 +
R2-Nere#debug xdsl ?
 +
  application  xDSL application
 +
  driver      xDSL driver
 +
  eoc          xDSL eoc
 +
  error        xDSL error
 +
 +
R2-Nere#debug xdsl app
 +
R2-Nere#debug xdsl application
 +
xDSL application debugging is on
 +
R2-Nere#debug xdsl driver
 +
xDSL driver debugging is on
 +
R2-Nere#debug xdsl error
 +
xDSL error debugging is on
 +
R2-Nere#
 +
R2-Nere#conf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
R2-Nere(config)#^Z
 +
R2-Nere#
 +
R2-Nere#show
 +
*Dec 16 03:12:13.227: %SYS-5-CONFIG_I: Configured from console by console contr
 +
R2-Nere#show  controllers ds
 +
R2-Nere#show  controllers dsL 0/2
 +
 +
DSL 0/2 controller DOWN
 +
SLOT 0: Globespan xDSL controller chipset
 +
DSL mode: Not Trained
 +
No frame mode configured
 +
Line Re-activated 0 times after system bootup
 +
LOSW Defect alarm: ACTIVE
 +
CRC per second alarm: ACTIVE
 +
Line termination: CPE
 +
FPGA Revision: 0xB2
 +
 +
        Current 15 min CRC: 0
 +
        Current 15 min LOSW Defect: 0
 +
        Current 15 min ES: 0
 +
        Current 15 min SES: 0
 +
        Current 15 min UAS: 0
 +
 +
        Previous 15 min CRC: 0
 +
        Previous 15 min LOSW Defect: 0
 +
        Previous 15 min ES: 0
 +
        Previous 15 min SES: 0
 +
        Previous 15 min UAS: 0
 +
 +
Line-0 status
 +
Chipset Version:  0
 +
Firmware Version:  R3.0.1
 +
Modem Status:  un checked mode, Status DF3D
 +
Last Fail Mode:  No Failure status:0x0
 +
Dying Gasp: Present
 +
 +
 +
R2-Nere#
 +
R2-Nere#show vers
 +
Cisco IOS Software, C2600 Software (C2600-IPBASEK9-M), Version 12.4(17a), RELEASE SOFTWARE (fc2)
 +
Technical Support: http://www.cisco.com/techsupport
 +
Copyright (c) 1986-2007 by Cisco Systems, Inc.
 +
Compiled Wed 07-Nov-07 12:40 by prod_rel_team
 +
 +
ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
 +
 +
R2-Nere uptime is 3 minutes
 +
System returned to ROM by power-on
 +
System image file is "flash:c2600-ipbasek9-mz.124-17a.bin"
 +
 +
 +
This product contains cryptographic features and is subject to United
 +
States and local country laws governing import, export, transfer and
 +
use. Delivery of Cisco cryptographic products does not imply
 +
third-party authority to import, export, distribute or use encryption.
 +
Importers, exporters, distributors and users are responsible for
 +
compliance with U.S. and local country laws. By using this product you
 +
agree to comply with applicable laws and regulations. If you are unable
 +
to comply with U.S. and local laws, return this product immediately.
 +
 +
A summary of U.S. laws governing Cisco cryptographic products may be found at:
 +
 +
R2-Nere#show  controllers dsL 0/2 | i Modem
 +
Modem Status:  un checked mode, Status DF3D
 +
R2-Nere#show  controllers dsL 0/2 | Rev
 +
                                      ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere#show  controllers dsL 0/2 | i Rev
 +
FPGA Revision: 0xB2
 +
R2-Nere#show  controllers dsL 0/2
 +
 +
DSL 0/2 controller DOWN
 +
SLOT 0: Globespan xDSL controller chipset
 +
DSL mode: Not Trained
 +
No frame mode configured
 +
Line Re-activated 0 times after system bootup
 +
LOSW Defect alarm: ACTIVE
 +
CRC per second alarm: ACTIVE
 +
Line termination: CPE
 +
FPGA Revision: 0xB2
 +
 +
        Current 15 min CRC: 0
 +
        Current 15 min LOSW Defect: 0
 +
        Current 15 min ES: 0
 +
        Current 15 min SES: 0
 +
        Current 15 min UAS: 0
 +
 +
        Previous 15 min CRC: 0
 +
        Previous 15 min LOSW Defect: 0
 +
        Previous 15 min ES: 0
 +
        Previous 15 min SES: 0
 +
        Previous 15 min UAS: 0
 +
 +
Line-0 status
 +
Chipset Version:  0
 +
Firmware Version:  R3.0.1
 +
Modem Status:  un checked mode, Status DF3D
 +
Last Fail Mode:  No Failure status:0x0
 +
Dying Gasp: Present
 +
 +
 +
R2-Nere#show  controllers dsL 0/2 | i Firm
 +
Firmware Version:  R3.0.1
 +
R2-Nere#show  controllers dsL
 +
 +
DSL 0/2 controller DOWN
 +
SLOT 0: Globespan xDSL controller chipset
 +
DSL mode: Not Trained
 +
No frame mode configured
 +
Line Re-activated 0 times after system bootup
 +
LOSW Defect alarm: ACTIVE
 +
CRC per second alarm: ACTIVE
 +
Line termination: CPE
 +
FPGA Revision: 0xB2
 +
 +
        Current 15 min CRC: 0
 +
        Current 15 min LOSW Defect: 0
 +
        Current 15 min ES: 0
 +
        Current 15 min SES: 0
 +
        Current 15 min UAS: 0
 +
 +
        Previous 15 min CRC: 0
 +
        Previous 15 min LOSW Defect: 0
 +
        Previous 15 min ES: 0
 +
        Previous 15 min SES: 0
 +
        Previous 15 min UAS: 0
 +
 +
Line-0 status
 +
Chipset Version:  0
 +
Firmware Version:  R3.0.1
 +
Modem Status:  un checked mode, Status DF3D
 +
Last Fail Mode:  No Failure status:0x0
 +
Dying Gasp: Present
 +
 +
 +
R2-Nere#
 +
R2-Nere#
 +
% Please answer 'yes' or 'no'.
 +
Would you like to enter the initial configuration dialog? [yes/no]:
 +
% Please answer 'yes' or 'no'.
 +
Would you like to enter the initial configuration dialog? [yes/no]: yes
 +
 +
At any point you may enter a question mark '?' for help.
 +
Use ctrl-c to abort configuration dialog at any prompt.
 +
Default settings are in square brackets '[]'.
 +
 +
Basic management setup configures only enough connectivity
 +
for management of the system, extended setup will ask you
 +
to configure each interface on the system
 +
 +
Would you like to enter basic management setup? [yes/no]:
 +
 +
 +
 +
Press RETURN to get started!
 +
 +
 +
*Mar  1 00:00:07.564: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
 +
*Mar  1 00:00:21.367: %SYS-3-NOELEMENT: data_enqueue:Ran out of buffer elements for enqueue
 +
-Process= "<interrupt level>", ipl= 6, pid= 3
 +
-Traceback= 80F791B0 80410240 801F7060 801F7144 801E1B1C 801F424C 801F424C 801E1BDC 801F405C 801F75AC 80F8A200 80F8B5D4 80F8AB74 81ECD37C 81CB4DA4 81CB4E5C
 +
*Mar  1 00:00:27.108: %SYS-6-LOGGERSTART: Logger process started
 +
*Mar  1 00:00:27.400: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
 +
*Mar  1 00:00:27.400: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
 +
*Mar  1 00:00:28.402: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
 +
*Mar  1 00:00:28.402: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
 +
*Jan 19 05:08:47.055: %SYS-5-RESTART: System restarted --
 +
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T1
 +
Router>1, RELEASE SOFTWARE (fc3)
 +
Technical Support: http://www.cisco.com/techsupport
 +
Copyright (c) 1986-2006 by Cisco Systems, Inc.
 +
Compiled Thu 24-Aug-06 17:56 by dchih
 +
*Jan 19 05:08:47.055: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
 +
*Jan 19 05:08:47.087: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down
 +
*Jan 19 05:08:47.091: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
 +
Router>ena
 +
Router#conf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
Router(config)#hostname r1-uppe
 +
r1-uppe(config)#^Z
 +
r1-uppe#
 +
r1-uppe#wr
 +
Building configuration...
 +
 +
*Jan 19 05:09:05.834: %SYS-5-CONFIG_I: Configured from console by console[OK]
 +
r1-uppe#
 +
r1-uppe#
 +
r1-uppe#show vers
 +
r1-uppe#show version | i 12.
 +
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T11, RELEASE SOFTWARE (fc3)
 +
ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
 +
System image file is "flash:c2600-advipservicesk9-mz.123-11.T11.bin"
 +
Cisco 2611XM (MPC860P) processor (revision 0x401) with 124858K/6214K bytes of memory.
 +
Processor board ID FTX1121A219 (2454220871)
 +
r1-uppe#
 +
r1-uppe#show contr
 +
r1-uppe#show controllers ds
 +
r1-uppe#show controllers dsL
 +
 +
DSL 0/0 controller DOWN
 +
SLOT 0: Globespan xDSL controller chipset
 +
No frame mode configured
 +
Line Re-activated 0 times after system bootup
 +
LOSW Defect alarm: ACTIVE
 +
CRC per second alarm: ACTIVE
 +
Line termination: CPE
 +
FPGA Revision: 0xA9
 +
 +
        Current 15 min CRC: 0
 +
        Current 15 min LOSW Defect: 0
 +
        Current 15 min ES: 0
 +
        Current 15 min SES: 0
 +
        Current 15 min UAS: 0
 +
 +
        Previous 15 min CRC: 0
 +
        Previous 15 min LOSW Defect: 0
 +
        Previous 15 min ES: 0
 +
        Previous 15 min SES: 0
 +
        Previous 15 min UAS: 0
 +
 +
Line-0 status
 +
Chipset Version:  1
 +
Firmware Version:  A29733
 +
Modem Status:  un checked mode, Status F5B9
 +
Last Fail Mode:  No Failure status:0x0
 +
Dying Gasp: Present
 +
 +
 +
r1-uppe#
 +
r1-uppe#
 +
r1-uppe# show ver | i 12.
 +
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T11, RELEASE SOFTWARE (fc3)
 +
ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
 +
System image file is "flash:c2600-advipservicesk9-mz.123-11.T11.bin"
 +
Cisco 2611XM (MPC860P) processor (revision 0x401) with 124858K/6214K bytes of memory.
 +
Processor board ID FTX1121A219 (2454220871)
 +
r1-uppe#
 +
r1-uppe#controller DSL 0/3/0
 +
          ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe#  mode atm
 +
              ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe#! Change to CPE on other end
 +
r1-uppe#  line-term co
 +
            ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe#  dsl-mode shdsl symmetric annex A
 +
            ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe#  line-rate auto
 +
            ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe#conf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
r1-uppe(config)#controller DSL 0/3/0
 +
                                ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config)#  mode atm
 +
                      ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config)#! Change to CPE on other end
 +
r1-uppe(config)#  line-term co
 +
                      ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config)#  dsl-mode shdsl symmetric annex A
 +
                    ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config)#  line-rate auto
 +
                      ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config)#controller DSL 0/2
 +
                                ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config)#do show run
 +
Building configuration...
 +
 +
Current configuration : 768 bytes
 +
!
 +
version 12.3
 +
service timestamps debug datetime msec
 +
service timestamps log datetime msec
 +
no service password-encryption
 +
!
 +
hostname r1-uppe
 +
!
 +
boot-start-marker
 +
boot-end-marker
 +
!
 +
!
 +
no network-clock-participate slot 1
 +
no network-clock-participate wic 0
 +
no aaa new-model
 +
ip subnet-zero
 +
ip cef
 +
!
 +
!
 +
!
 +
!
 +
ip ips po max-events 100
 +
no ftp-server write-enable
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
controller DSL 0/0
 +
line-term cpe
 +
!
 +
controller E1 1/0
 +
!
 +
 +
r1-uppe(config)#controller DSL 0/0
 +
r1-uppe(config-controller)#  mode atm
 +
r1-uppe(config-controller)#  dsl-mode shdsl symmetric annex A
 +
*Jan 19 05:16:29.120: %CONTROLLER-5-UPDOWN: Contro  line-term co
 +
r1-uppe(config-controller)#controller DSL 0/0
 +
*Jan 19 05:16:35.911: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, cha  dsl-mode shdsl symmetric annex A
 +
r1-uppe(config-controller)#  mode atm
 +
*Jan 19 05:16:41.024: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed st  line-rate auto      r1-uppe(config-controller)#
 +
r1-uppe(config-controller)#
 +
*Jan 19 05:16:51.249: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
 +
r1-uppe(config-controller)#^Z
 +
r1-uppe#
 +
r1-uppe#
 +
*Jan 19 05:16:54.991: %SYS-5-CONFIG_I: Configured from console by console
 +
r1-uppe#
 +
R2-Nere#
 +
R2-Nere#conf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
R2-Nere(config)#controller DSL 0/3/0
 +
                                ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere(config)#  mode atm
 +
                      ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere(config)#! Change to CPE on other end
 +
R2-Nere(config)#  line-term co
 +
                      ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere(config)#  dsl-mode shdsl symmetric annex A
 +
                    ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere(config)#  line-rate auto
 +
                      ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere(config)#interf dsl 0/0
 +
                        ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere(config)#do show run
 +
Building configuration...
 +
 +
Current configuration : 753 bytes
 +
!
 +
version 12.4
 +
service timestamps debug datetime msec
 +
service timestamps log datetime msec
 +
no service password-encryption
 +
!
 +
hostname R2-Nere
 +
!
 +
boot-start-marker
 +
boot-end-marker
 +
!
 +
!
 +
no aaa new-model
 +
memory-size iomem 10
 +
no network-clock-participate slot 1
 +
no network-clock-participate wic 0
 +
ip cef
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
controller DSL 0/2
 +
line-term cpe
 +
!
 +
!
 +
!
 +
interface FastEthernet0/0
 +
no ip address
 +
shutdown
 +
duplex auto
 +
speed auto
 +
!
 +
interface Serial0/0
 +
no ip address
 +
shutdown
 +
no fair-queue
 +
!
 +
interface FastEthernet0/1
 +
no ip address
 +
 +
R2-Nere(config)#interf dsl 0/2
 +
                        ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere(config)#contr dsl 0/2
 +
R2-Nere(config-controller)#  mode atm
 +
R2-Nere(config-controller)#contr dsl 0/2
 +
*Dec 16 03:26:35.571: DSL 0/2 gsi_shdsl_set_frame_mode(): mode change
 +
*Dec 16 03:26:36.135: DSL 0/2 gsi_shdsl_set_frame_mode(): mode change
 +
*Dec 16 03:26:36.163: DSL 0/2  xdsl_mode_commandDownload indication
 +
*Dec 16 03:26:36.167: DSL 0/2 process_get_wakeup
 +
*Dec 16 03:26:36.167: DSL 0/2 xdsl_background_process:Download boolean event received
 +
*Dec 16 03:26:36.167: DSL 0/2 xdsl_controller_reset: cdb-state=down
 +
*Dec 16 03:26:36.167: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, changed interf dsl 0/2
 +
*Dec 16 03:26:36.167: DSL 0/2 gsi_shdsl_reset()
 +
*Dec 16 03:26:36.167: DSL 0/2  xdsl_gsi_int_disable(true):: 0x0
 +
*Dec 16 03:26:36.171: DSL 0/2 xcvr_ptr=825577F0
 +
*Dec 16 03:26:36.275: DSL 0/2 Func:gsi_shdsl_shutdown, Line184fail to abort for shutdown
 +
*Dec 16 03:26:36.319: DSL 0/2  SHDSL Line activation started, please wait
 +
*Dec 16 03:26:36.319: DSL 0/2 DSP interrupt enabled
 +
*Dec 16 03:26:36.319: DSL 0/2 Framer interrupt disabled
 +
*Dec 16 03:26:36.319: DSL 0/2
 +
*Dec 16 03:26:36.319: Setting GTI_NTR_LOCAL_OSC
 +
*Dec 16 03:26:36.323: DSL 0/2  xdsl_gsi_int_disable(false):: 0x1
 +
*Dec 16 03:26:36.387: DSL 0/2  dsp interrupt-download next block for line-0
 +
*Dec 16 03:26:36.411: DSL 0/2 framer intr_status 0xC0
 +
*Dec 16 03:26:36.511: DSL 0/2  dsp interrupt-download next block for line-0
 +
*Dec 16 03:26:36.519: DSL 0/2 framer intr_status 0xC0
 +
*Dec 16 03:26:37.323: DSL 0/2 process_get_wakeup
 +
*Dec 16 03:26:38.323: DSL 0/2 process_get_wakeup
 +
*Dec 16 03:26:39.323: DSL 0/2 process_get_wakeup
 +
*Dec 16 03:26:40.323: DSL 0/2 process_get_wakeup
 +
*Dec 16 03:26:41.323: DSL 0/2 process_get_wakeup
 +
*Dec 16 03:26:42.323: DSL 0/2 process_get_wakeup
 +
*Dec 16 03:26:43.323: DSL 0/2 process_get_wakeup^Z                                  ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere#u
 +
*Dec 16 03:26:43.643: %SYS-5-CONFIG_I: Configured from console by consolen all
 +
All possible debugging has been turned off
 +
R2-Nere#
 +
*Dec 16 03:26:44.323: DSL 0/2 process_get_wakeupconf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
R2-Nere(config)#  line-term cpe
 +
                      ^
 +
% Invalid input detected at '^' marker.
 +
 +
R2-Nere(config)#  line-
 +
R2-Nere(config)#  line?
 +
line
 +
 +
R2-Nere(config)#  line ?
 +
  <0-70>  First Line number
 +
  aux      Auxiliary line
 +
  console  Primary terminal line
 +
  tty      Terminal controller
 +
  vty      Virtual terminal
 +
  x/y      Slot/Port for Modems
 +
 +
R2-Nere(config)#control
 +
R2-Nere(config)#controll
 +
R2-Nere(config)#controller ds
 +
R2-Nere(config)#controller dsL 0/2
 +
R2-Nere(config)#controller dsL 0/2
 +
R2-Nere(config-controller)#  line-term cpe
 +
R2-Nere(config-controller)#  dsl-mode shdsl symmetric annex A
 +
R2-Nere(config-controller)#controller dsL 0/2
 +
*Dec 16 03:27:23.067: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, chainterf dsl 0/2
 +
R2-Nere(config-controller)#  line-rate auto
 +
R2-Nere(config-controller)#
 +
*Dec 16 03:27:38.211: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, changed state to down^Z
 +
R2-Nere#
 +
R2-Nere#
 +
R2-Nere#sh
 +
*Dec 16 03:27:39.475: %SYS-5-CONFIG_I: Configured from console by consoleow run | se DSL
 +
controller DSL 0/2
 +
mode atm
 +
line-term cpe
 +
line-mode 2-wire line-zero
 +
dsl-mode shdsl symmetric annex A
 +
line-rate auto
 +
R2-Nere#
 +
r1-uppe#show run | se DSL
 +
controller DSL 0/0
 +
mode atm
 +
line-term co
 +
line-mode 2-wire line-zero
 +
dsl-mode shdsl symmetric annex A
 +
line-rate auto
 +
r1-uppe#
 +
r1-uppe#debug xdsl
 +
r1-uppe#debug xdsl ?
 +
  application  xDSL application
 +
  driver      xDSL driver
 +
  eoc          xDSL eoc
 +
  error        xDSL error
 +
 +
r1-uppe#debug xdsl error
 +
xDSL error debugging is on
 +
r1-uppe#debug xdsl dri
 +
r1-uppe#debug xdsl driver
 +
xDSL driver debugging is on
 +
r1-uppe#debug xdsl app
 +
xDSL application debugging is on
 +
r1-uppe#
 +
*Jan 19 05:20:07.863: DSL 0/0 process_get_wakeup
 +
*Jan 19 05:20:08.865: DSL 0/0 process_get_wakeup
 +
*Jan 19 05:20:09.866: DSL 0/0 process_get_wakeup
 +
*Jan 19 05:20:10.868: DSL 0/0 process_get_wakeupdebug xdsl app
 +
*Jan 19 05:20:11.869: DSL 0/0 process_get_wakeup
 +
*Jan 19 05:20:12.871: DSL 0/0 process_get_wakeupno debug xdsl app
 +
xDSL application debugging is off
 +
r1-uppe#
 +
*Jan 19 05:20:13.873: DSL 0/0 process_get_wakeupno debug xdsl error
 +
xDSL error debugging is off
 +
r1-uppe#
 +
r1-uppe#
 +
r1-uppe#
 +
r1-uppe#debug xdsl error
 +
xDSL error debugging is on
 +
r1-uppe#
 +
*Jan 19 05:21:22.629: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:22.637: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:28.030: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:28.038: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:33.467: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:33.491: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:33.567: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:33.587: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:33.688: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:33.696: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:36.484: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:36.488: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:36.785: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:36.801: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:37.157: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:37.169: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:39.798: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:39.802: DSL 0/0 framer intr_status 0xC0
 +
r1-uppe#  line-rate auto
 +
*Jan 19 05:21:53.260: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:53.264: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:53.704: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:53.712: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:53.905: DSL 0/0  dsp interrupt-download next block for line-0
 +
*Jan 19 05:21:53.909: DSL 0/0 DSP interrupt disabled
 +
*Jan 19 05:21:53.909: DSL 0/0  Download completed for line-0
 +
*Jan 19 05:21:53.913: DSL 0/0 Framer interrupt enabled
 +
*Jan 19 05:21:53.913: DSL 0/0 framer intr_status 0xC0
 +
*Jan 19 05:21:53.913:  DSL 0/0 controller Link up! line rate: 2304 Kbps
 +
 +
'''*Jan 19 05:21:53.917: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to up'''
 +
*Jan 19 05:21:54.017: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:21:54.017: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.021: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.113: DSL 0/0 framer intr_status 0xC1
 +
*Jan 1conf tSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.113: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.133: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:54.133: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.133: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.209: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:21:54.209: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.209: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.225: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:54.229: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.229: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.305: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:21:54.305: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.305: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.321: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:54.325: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.325: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.418: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:54.422: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.422: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.514: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:54.518: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.518: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:54.522: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:54.522: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:54.522: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.009: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:21:59.009: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.009: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.013: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:59.017: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.017: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.021: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:59.021: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.021: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.105: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:21:59.105: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.105: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.121: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:59.125: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.125: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.201: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:21:59.201: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.201: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.217: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:59.221: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.221: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.298: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:21:59.298: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.298: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.314: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:59.318: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.318: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:21:59.322: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:21:59.322: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:21:59.322: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1un all
 +
              ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe#
 +
*Jan 19 05:22:04.005: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:22:04.009: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.009: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:04.013: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:22:04.013: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:22:04.013: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.013: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:04.109: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:22:04.109: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.109: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:04.125: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:22:04.129: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.129: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:04.206: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:22:04.206: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.206: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:04.222: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:22:04.226: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.226: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:04.302: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:22:04.302: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.302: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:04.318: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:22:04.322: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.322: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:04.326: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:22:04.326: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:04.326: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1^Z
 +
r1-uppe#un all
 +
All possible debugging has been turned off
 +
r1-uppe#
 +
*Jan 19 05:22:09.005: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:22:09.005: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:09.005: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:09.009: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:22:09.014: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:09.014: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:09.018: DSL 0/0 framer intr_status 0xC4
 +
*Jan 19 05:22:09.018: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:09.018: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:09.102: DSL 0/0 framer intr_status 0xC1
 +
*Jan 19 05:22:09.102: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
 +
*Jan 19 05:22:09.102: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
 +
*Jan 19 05:22:09.118: DSL 0/0 framer intr_status 0xC4
 +
r1-uppe#
 +
r1-uppe#show ip interf bri
 +
Interface                  IP-Address      OK? Method Status                Protocol
 +
ATM0/0                    unassigned      YES unset  initializing          down
 +
FastEthernet0/0            unassigned      YES unset  administratively down down
 +
FastEthernet0/1            unassigned      YES unset  administratively down down
 +
r1-uppe#
 +
r1-uppe#
 +
*Jan 19 05:22:20.396: %LINK-3-UPDOWN: Interface ATM0/0, changed state to up
 +
*Jan 19 05:22:21.398: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to up
 +
r1-uppe#
 +
r1-uppe#
 +
r1-uppe#show ip interf bri
 +
Interface                  IP-Address      OK? Method Status                Protocol
 +
'''ATM0/0                    unassigned      YES unset  up                    up'''
 +
FastEthernet0/0            unassigned      YES unset  administratively down down
 +
FastEthernet0/1            unassigned      YES unset  administratively down down
 +
r1-uppe#
 +
r1-uppe#
 +
r1-uppe#show atm vc
 +
          VCD /                                        Peak  Avg/Min Burst
 +
Interface  Name        VPI  VCI  Type  Encaps  SC  Kbps  Kbps  Cells  Sts
 +
r1-uppe#
 +
r1-uppe#show run | sec ATM
 +
interface ATM0/0
 +
no ip address
 +
no atm ilmi-keepalive
 +
r1-uppe#conf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
r1-uppe(config)#interf atm 0/0
 +
r1-uppe(config-if)#no ip address
 +
r1-uppe(config-if)# load-interval 30
 +
r1-uppe(config-if)# no atm ilmi-keepalive
 +
r1-uppe(config-if)# clock rate aal5 8000000
 +
                                          ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config-if)# clock rate aal5 ?
 +
        1000000
 +
        1300000
 +
        1600000
 +
        2000000
 +
        2600000 (default)
 +
        3200000
 +
        4000000
 +
        5300000
 +
        7000000
 +
 +
  <1000000-7000000>  clock rates in bits per second, choose one from above
 +
 +
r1-uppe(config-if)# clock rate aal5 7000000
 +
%ATM0/0 Resetting interface...
 +
r1-uppe(config-if)#
 +
*Jan 19 05:25:37.235: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
 +
*Jan 19 05:25:37.752: %LINK-3-UPDOWN: Interface ATM0/0, changed state to down
 +
*Jan 19 05:25:38.753: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to down
 +
r1-uppe(config-if)#no  clock rate aal5 7000000
 +
%Defaulting to 2600000 bps
 +
%ATM0/0: Bringing interface up...
 +
r1-uppe(config-if)#
 +
*Jan 19 05:25:54.752: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
 +
r1-uppe(config-if)#
 +
r1-uppe(config-if)#show ip interf bri
 +
                    ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config-if)#do show ip interf bri
 +
Interface                  IP-Address      OK? Method Status                Protocol
 +
ATM0/0                    unassigned      YES manual down                  down
 +
FastEthernet0/0            unassigned      YES unset  administratively down down
 +
FastEthernet0/1            unassigned      YES unset  administratively down down
 +
r1-uppe(config-if)#
 +
r1-uppe(config-if)#show atm vc
 +
                    ^
 +
% Invalid input detected at '^' marker.
 +
 +
r1-uppe(config-if)#do show atm vc
 +
          VCD /                                        Peak  Avg/Min Burst
 +
Interface  Name        VPI  VCI  Type  Encaps  SC  Kbps  Kbps  Cells  Sts
 +
r1-uppe(config-if)#do show run | sec ATM
 +
interface ATM0/0
 +
no ip address
 +
load-interval 30
 +
no atm ilmi-keepalive
 +
r1-uppe(config-if)#
 +
*Jan 19 05:27:02.142:  DSL 0/0 controller Link up! line rate: 2304 Kbps
 +
 +
*Jan 19 05:27:02.142: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to up
 +
r1-uppe(config-if)#
 +
r1-uppe(config-if)#interf atm
 +
*Jan 19 05:27:30.408: %LINK-3-UPDOWN: Interface ATM0/0, changed state to up
 +
*Jan 19 05:27:31.410: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to up0/0
 +
r1-uppe(config-if)#interf atm 0/0.1 po
 +
r1-uppe(config-if)#interf atm 0/0.1 poi
 +
r1-uppe(config-if)#interf atm 0/0.1 point-to-point
 +
r1-uppe(config-subif)#ip address 1.1.1.1 255.255.255.0
 +
r1-uppe(config-subif)#pvc 2/100
 +
r1-uppe(config-if-atm-vc)#  vbr-rt 2000 2000
 +
r1-uppe(config-if-atm-vc)#  oam-pvc 0
 +
r1-uppe(config-if-atm-vc)#  encapsulation aal5mux ip
 +
r1-uppe(config-if-atm-vc)#^Z
 +
r1-uppe#
 +
r1-uppe#
 +
*Jan 19 05:28:37.839: %ATM-5-UPDOWN: Interface ATM0/0.1, Changing autovc 2/100 to PVC activated.
 +
*Jan 19 05:28:37.839: %ATM-5-UPDOWN: Interface ATM0/0.1, Changing autovc 2/100 to PVC created.
 +
*Jan 19 05:28:37.839: %SYS-5-CONFIG_I: Configured from console by console
 +
r1-uppe#show atm vc
 +
          VCD /                                        Peak  Avg/Min Burst
 +
Interface  Name        VPI  VCI  Type  Encaps  SC  Kbps  Kbps  Cells  Sts
 +
0/0.1      1              2  100  PVC    MUX      VBR    2000  2000    0  UP
 +
r1-uppe#
 +
R2-Nere>ena
 +
R2-Nere#conf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
R2-Nere(config)#
 +
r1-uppe#show running | sec ATM
 +
interface ATM0/0
 +
no ip address
 +
load-interval 30
 +
no atm ilmi-keepalive
 +
interface ATM0/0.1 point-to-point
 +
ip address 1.1.1.1 255.255.255.0
 +
pvc 2/100
 +
  vbr-rt 2000 2000
 +
  oam-pvc 0
 +
  encapsulation aal5mux ip
 +
!
 +
r1-uppe#
 +
R2-Nere(config)#interf atm 0/2
 +
R2-Nere(config-if)# load-interval 30
 +
R2-Nere(config-if)# no atm ilmi-keepalive
 +
R2-Nere(config-if)#exit
 +
R2-Nere(config)#interf atm 0/2.1 point
 +
R2-Nere(config)#interf atm 0/2.1 point-to-point
 +
R2-Nere(config-subif)#ip address 1.1.1.2 255.255.255.0
 +
R2-Nere(config-subif)# pvc 2/100
 +
R2-Nere(config-if-atm-vc)#  vbr-rt 2000 2000
 +
R2-Nere(config-if-atm-vc)#  oam-pvc 0
 +
R2-Nere(config-if-atm-vc)#  encapsulation aal5mux ip
 +
R2-Nere(config-if-atm-vc)#^Z
 +
R2-Nere#
 +
R2-Nere#
 +
*Dec 16 03:39:25.327: %SYS-5-CONFIG_I: Configured from console by console
 +
R2-Nere#show atm vc
 +
          VCD /                                        Peak  Avg/Min Burst
 +
Interface  Name        VPI  VCI  Type  Encaps  SC  Kbps  Kbps  Cells  Sts
 +
0/2.1      1              2  100  PVC    MUX      VBR    2000  2000    0  UP
 +
R2-Nere#ping 1.1.1.1
 +
 +
Type escape sequence to abort.
 +
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
 +
!!!!!
 +
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms
 +
R2-Nere#show atm vc
 +
          VCD /                                        Peak  Avg/Min Burst
 +
Interface  Name        VPI  VCI  Type  Encaps  SC  Kbps  Kbps  Cells  Sts
 +
0/2.1      1              2  100  PVC    MUX      VBR    2000  2000    0  UP
 +
R2-Nere#conf t
 +
Enter configuration commands, one per line.  End with CNTL/Z.
 +
R2-Nere(config)#line vty 0 15
 +
R2-Nere(config-line)#login
 +
% Login disabled on line 66, until 'password' is set
 +
% Login disabled on line 67, until 'password' is set
 +
% Login disabled on line 68, until 'password' is set
 +
% Login disabled on line 69, until 'password' is set
 +
% Login disabled on line 70, until 'password' is set
 +
% Login disabled on line 71, until 'password' is set
 +
% Login disabled on line 72, until 'password' is set
 +
% Login disabled on line 73, until 'password' is set
 +
% Login disabled on line 74, until 'password' is set
 +
% Login disabled on line 75, until 'password' is set
 +
% Login disabled on line 76, until 'password' is set
 +
% Login disabled on line 77, until 'password' is set
 +
% Login disabled on line 78, until 'password' is set
 +
% Login disabled on line 79, until 'password' is set
 +
% Login disabled on line 80, until 'password' is set
 +
% Login disabled on line 81, until 'password' is set
 +
R2-Nere(config-line)#passw
 +
R2-Nere(config-line)#password cisco
 +
R2-Nere(config-line)#
 +
R2-Nere(config-line)#
 +
R2-Nere(config-line)#^Z
 +
R2-Nere#
 +
R2-Nere#
 +
*Dec 16 03:40:12.839: %SYS-5-CONFIG_I: Configured from console by console
 +
r1-uppe#show ip interf bri
 +
Interface                  IP-Address      OK? Method Status                Protocol
 +
ATM0/0                    unassigned      YES manual up                    up
 +
ATM0/0.1                  1.1.1.1        YES manual up                    up
 +
FastEthernet0/0            unassigned      YES unset  administratively down down
 +
FastEthernet0/1            unassigned      YES unset  administratively down down
 +
r1-uppe#1.1.1.2
 +
Trying 1.1.1.2 ... Open
 +
 +
 +
User Access Verification
 +
 +
Password:
 +
R2-Nere>exit
 +
 +
[Connection to 1.1.1.2 closed by foreign host]
 +
r1-uppe#
 +
r1-uppe#show atm vc
 +
          VCD /                                        Peak  Avg/Min Burst
 +
Interface  Name        VPI  VCI  Type  Encaps  SC  Kbps  Kbps  Cells  Sts
 +
0/0.1      1              2  100  PVC    MUX      VBR    2000  2000    0  UP
 +
r1-uppe#
 +
r1-uppe#
 +
</pre>

Latest revision as of 06:29, 15 August 2017

Contents

[edit] Experiments with DSL cards

HWIC-4SHDSL   WIC-1SHDSL-V2
HWIC 4SHDSL -- Card in 2600-routers   WIC-1SHDSL-V2 -- Card in 2600-routers
Card in 2900 routers (8pin pink RJ45 port)   Card in old 2600 routers (6pin pink RJ12 port)


[edit] Documentation

[edit] Laboration

Laboration

  1. Configure Hostnames "Router2900" and "Router2600" to your routers !
  2. Figure out which slot your DSL card is in by using the commands: 
    Router2900#show controller shdsl
    Router2600#show controller dsl
    Answers: 2900-Slot _____________ and 2600-Slot _____________
  3. Try the commands 
    show running
    and find all lines that include controller and dsl on both routers
    Answer: 2600 ________________
    Answer: 2900 ________________
  4. What is the difference between interface serial 0/0 and controller serial 0/0  ?
  5. How many ATM interfaces exists in show running
    Answer: ______________

[edit] 2900 SETUP

  1. Configure the DSL controller of the 2900
    controller SHDSL 0/3/0
      description This is the CPE
      ! Automatically assign the Central Office (CO) configuration to
      ! an ATM dsl-group on the Customer Premise Equipment (CPE).
      dsl-group auto

DIDN'T WORK, PLEASE USE 

controller SHDSL 0/3/0
  description Can *only* run in CPE mode
  dsl-group 0 pairs  0, 1
    shdsl 4-wire mode enhanced
    shdsl annex A
    shdsl rate 4096
  !
  1. How many ATM interfaces exists in show running
    Answer: ______________
  2. Configure the ATM interface of the 2900
    interface ATM 0/3/0
      no ip address
      load-interval 30
      no atm ilmi-keepalive
  3. Try the command show ip interface brief
  4. Create a ATM subinterface with a Layer2 VPI/VCI and a Layer3 IP-address
    interface ATM 0/3/0.1 point-to-point
      description Connection to Router2600 (Central Office)
      ip address 1.1.1.2 255.255.255.0
      pvc 2/100
        vbr-rt 2000 2000
        oam-pvc manage auto-detect
        encapsulation aal5mux ip
  5. Try the command show ip interface brief

[edit] 2600 SETUP

  1. How many ATM interfaces exists in show running
    Answer: ______________
  2. Try the command show ip interface brief
  3. Configure the DSL controller of the 2600
    controller DSL 0/2
    description This is CO, the other end is CPE
    mode atm
    line-term co
    line-mode 4-wire
    dsl-mode shdsl symmetric annex A
    line-rate 4096
  4. How many ATM interfaces exists in show running
    Answer: ______________
  5. Configure the ATM interface of the 2600
    interface ATM 0/2
    description ATM over DSL (Central Office)
    no ip address
    load-interval 30
    no atm ilmi-keepalive
  6. Try the command show ip interface brief
  7. Create a ATM subinterface with a Layer2 VPI/VCI and a Layer3 IP-address
    interface ATM 0/2.1 point-to-point
      description Connection to Router2900 (Customer)
      ip address 1.1.1.1 255.255.255.0
      pvc 2/100
        vbr-rt 2000 2000
        no oam-pvc manage
        encapsulation aal5mux ip
  8. Try the command show ip interface brief
    You might get:
    ATM0/2 unassigned YES manual initializing down
    ATM0/2.1 1.1.1.1 YES manual initializing down
  9. Let's ping the other end !!
  10. Ûberkurz:
    1. What show-command shows the line-speed of the xDSL controller
    2. What show-command shows if the controller is running as CPE or CO
    3. What ATM AAL options are available on both cards?
      Are there any special PPP settings that are required to make communication work? Try!
    4. What is the theory behind the PVC's?
      Are there any special control PVC's (like 0/32 ?!?) ?

[edit] MINIMAL 29/4

Router2600#show running | sec ATM|DSL 

controller DSL 0/2
  description This is CO, the other end is CPE
  mode atm
  line-term co
  line-mode 2-wire line-zero
  dsl-mode shdsl symmetric annex B
  line-rate 2048
interface ATM0/2.1 point-to-point
  ip address 1.1.1.1 255.255.255.0
  ipv6 address 2001::1/64
  cdp enable
pvc 2/100
  encapsulation aal5snap
!

Router2900#show run | sec DSL|ATM
controller SHDSL 0/3/0
  description Can *only* run in CPE mode
  dsl-group auto
interface ATM0/3/0.1 point-to-point
  ip address 1.1.1.2 255.255.255.0
  ipv6 address 2001::2/64
  cdp enable
  pvc 2/100
    encapsulation aal5snap
!

[edit] How to do it 

! On 2801 running IOS  (C2801-ADVIPSERVICESK9-M), Version 12.4(24)T
! #show controller dsl | inc Firmware|prog
!  Firmware Version:  R4.2.1
! 

! Fungerar INTE
!   2801 Software (C2801-ADVIPSERVICESK9-M), Version 15.1(4)M6
! show controll DSL | i Firm|prog
!   Firmware Version:  388.132
!   DSL firmware download in progress, please wait



! make the DSL-controller create the ATM interface
 controller DSL 0/3/0                                   controller SHDSL 0/3/0
   mode atm                                               dsl-group auto
! Change to CPE on other end
   line-term co                                           
 line-mode 2-wire line-zero
 dsl-mode shdsl symmetric annex A                         shdsl annex A
 line-rate auto                                           !shdsl rate -- Only on CO side !!

! Configure the ATM interface
interface ATM 0/3/0                               <-- SAME for 2901 gh.shDSL
  no ip address
  load-interval 30
  no atm ilmi-keepalive
!
interface ATM 0/3/0.1 point-to-point
  ! Change to .2 on other end 
  ip address 1.1.1.1 255.255.255.0
  pvc 2/100 
    vbr-rt 2000 2000
    oam-pvc 0
    encapsulation aal5mux ip

show atm vc
           VCD /                                        Peak  Avg/Min Burst
Interface  Name         VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts
0/0.1      1              2   100  PVC    MUX      VBR    2000   2000     0   UP


Minimal Setup 

controller DSL 0/3/0
  mode atm
  line-term co
interface ATM0/3/0.1 point-to-point
  ip address 1.1.1.1 255.255.255.0
  pvc 2/100
    encapsulation aal5mux ip

[edit] Todays Errors 

 Hi,
to force CO mode you need to configure 'termination CO' under the controller SHDSL.
 However, only HWIC-4SHDSL supports that command. See here for reference:
 "Q. Do the G.SHDSL HWICs work in central-office mode (back-to-back connection without a DSLAM)?
 A. Currently only the HWIC-4SHDSL supports both CPE and central-office  modes for diagnostic purposes. The mode of operation can be set only  from the ROM Monitor environment. CPE is the default mode of operation."
[http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps7175/prod_qas0900aecd80591ff1.html
 http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps7175/prod_qas0900aecd80591ff1.html]

Hope this helps 

 Marco



 Router#show diag
 Slot 0:
       C2610 1E Mainboard Port adapter, 4 ports
 ...
 WIC Slot 1:
       Unknown WAN daughter card
       ...
       Product Number           : WIC-1SHDSL-V2
Router#show vers | inc 12
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(8)T5,  RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-i-mz.122-8.T5.bin"

Router2600#show diag
Slot 0:
       C2621 2FE Mainboard Port adapter, 5 ports
 ...
       WIC Slot 1:
       Unknown WAN daughter card

Router2600#show vers | inc 12
IOS (tm) C2600 Software (C2600-BIN-M), Version 12.3(25), RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-bin-mz.123-25.bin"
 
 show diag
      WIC Slot 1:
       GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
Router#show vers 
 Cisco IOS Software, C2600 Software (C2600-IPBASEK9-M), Version 12.4(17a), RELEASE SOFTWARE (fc2)
 System image file is "flash:c2600-ipbasek9-mz.124-17a.bin"
 Cisco 2621XM (MPC860P) processor (revision 1.0) with 59392K/6144K bytes of memory.




 show controller atM 0/3/0
  WIC Config Reg2   0x04       Gen bus error on bad G.SHDSL ATM/T1/E1 access
  ...
  Interface Serial0/3/0
 Hardware is GT96K
 DTE Unknown (13) RX clock detected.

    2901# show diag
       ...
       WIC Slot 3:
       GSI GSHDSL MULTI LINE ATM/T1/E1 WIC

       WIC module not supported/disabled in this slot
       Hardware Revision        : 0.0
       Top Assy. Part Number    : 800-23445-02
       Board Revision           : A0
       Deviation Number         : 78181
       Fab Version              : 04
       PCB Serial Number        : FOC09132CUJ
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Version Identifier       : V02
       Product (FRU) Number     : WIC-1SHDSL-V2

[edit] is it there ??

During boot 

Self decompressing the image :   
#########################################################################################
###########################################################################################
###########################################################################################
####################################################################### [OK]

IOMEM set to: 5
Unknown Card in slot 0
PMem allocated: 381681664 bytes; IOMem allocated: 20971520 bytes
...
...
Cisco 2801 (revision 7.0) with 372736K/20480K bytes of memory.
Processor board ID FCZ112070FT
1 DSL controller
2 FastEthernet interfaces
2 Serial(sync/async) interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)

Commands: 

show diag
  WIC/VIC/HWIC Slot 3:
       GSI GSHDSL MULTI LINE ATM/T1/E1 WIC
 
       Hardware Revision        : 0.0
       Top Assy. Part Number    : 800-23445-01
       Board Revision           : C0
       Deviation Number         : 0
       Fab Version              : 04
       PCB Serial Number        : FOC08170N9M
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Version Identifier       :
       Product (FRU) Number     :
       EEPROM format version 4

show running
 !
 controller DSL 0/3/0
 !

R1(config)#controller dsl 0/3/0
R1(config-controller)#?
Controller configuration commands:
  default                Set a command to its defaults
  description            Controller specific description
  dsl-mode               SHDSL mode
  exit                   Exit from controller configuration mode
  help                   Description of the interactive help system
  ignore-error-duration  Number of seconds errors such as CRC are ignored while
                         the line is training (default is 0)
  line-term              Customer Premise or Central Office
  loopback               XDSL loopback test
  mode                   Configure the xdsl controller mode
  no                     Negate a command or set its defaults
  shutdown               Shutdown the xdsl controller
  snr                    SNR
R1(config-controller)#


[edit] Debugging

clear

  • clear interface atm 0/3/0

show

  • show atm vc
  • show dsl interface atm 0/3/0 
* R1#show controllers dsl brief
DSL 0/3/0 controller DOWN
Globespan xDSL controller chipset
DSL mode: Not Trained
Frame mode: Utopia
Configured Line rate: 2048Kbps
Line Re-activated 0 times after system bootup
LOSW Defect alarm: ACTIVE
CRC per second alarm: ACTIVE
Line termination: CO
FPGA Revision: 0xB3
  • show controller DSL 0/3/0
  • show interfaces atm 0/3/0

debug

  • debug atm events
  • debug atm errors
  • debug xdsl driver

???

  • dslsar disable ATM0/3/0
  • dslsar enable ATM0/3/0

[edit] Latest BUG hunt

[edit] show controllers dsl 

! ON A CISCO 2801
Line-0 status
Chipset Version:  0
Firmware Version:  388.132
Modem Status:  Handshake, Status 10
Last Fail Mode:  No Failure status:0x0
DSL firmware download in progress, please wait
Dying Gasp: Present

! ON A 26x1 XM, IOS  12.4
Line-0 status
Chipset Version:  1
Firmware Version:  A29733
Modem Status:  un checked mode, Status F5B9
Last Fail Mode:  No Failure status:0x0
Dying Gasp: Present

! ON A 2611 XM, IOS   12.3(11)T11
Line-0 status
Chipset Version:  0
Firmware Version:  R3.0.1
Modem Status:  un checked mode, Status DF3D
Last Fail Mode:  No Failure status:0x0
Dying Gasp: Present

[edit] Så här gick det till när det fungerade första gången 

Router>
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname R2-Nere
R2-Nere(config)#^Z
R2-Nere#
R2-Nere#
*Dec 16 03:11:14.075: %SYS-5-CONFIG_I: Configured from console by consolewr
Building configuration...
[OK]
R2-Nere#
R2-Nere#show running
Building configuration... 

Current configuration : 753 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2-Nere
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
memory-size iomem 10
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
!
!
!
!
!
controller DSL 0/2
 line-term cpe
!
!
!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/0
 no ip address
 shutdown
 no fair-queue
!
interface FastEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/1
 no ip address
 shutdown
!
ip forward-protocol nd
!
ip http server
no ip http secure-server
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
!
!
end

[edit] pre 

R2-Nere#debug xds
R2-Nere#debug xdsl ?
  application  xDSL application
  driver       xDSL driver
  eoc          xDSL eoc
  error        xDSL error

R2-Nere#debug xdsl app
R2-Nere#debug xdsl application
xDSL application debugging is on
R2-Nere#debug xdsl driver
xDSL driver debugging is on
R2-Nere#debug xdsl error
xDSL error debugging is on
R2-Nere#
R2-Nere#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R2-Nere(config)#^Z
R2-Nere#
R2-Nere#show
*Dec 16 03:12:13.227: %SYS-5-CONFIG_I: Configured from console by console contr
R2-Nere#show  controllers ds
R2-Nere#show  controllers dsL 0/2

 DSL 0/2 controller DOWN
 SLOT 0: Globespan xDSL controller chipset
 DSL mode: Not Trained
 No frame mode configured
 Line Re-activated 0 times after system bootup
 LOSW Defect alarm: ACTIVE
 CRC per second alarm: ACTIVE
 Line termination: CPE
 FPGA Revision: 0xB2

        Current 15 min CRC: 0
        Current 15 min LOSW Defect: 0
        Current 15 min ES: 0
        Current 15 min SES: 0
        Current 15 min UAS: 0

        Previous 15 min CRC: 0
        Previous 15 min LOSW Defect: 0
        Previous 15 min ES: 0
        Previous 15 min SES: 0
        Previous 15 min UAS: 0

 Line-0 status
 Chipset Version:  0
 Firmware Version:  R3.0.1
 Modem Status:  un checked mode, Status DF3D
 Last Fail Mode:  No Failure status:0x0
 Dying Gasp: Present


R2-Nere#
R2-Nere#show vers
Cisco IOS Software, C2600 Software (C2600-IPBASEK9-M), Version 12.4(17a), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 07-Nov-07 12:40 by prod_rel_team

ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)

R2-Nere uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:c2600-ipbasek9-mz.124-17a.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

R2-Nere#show  controllers dsL 0/2 | i Modem
 Modem Status:  un checked mode, Status DF3D
R2-Nere#show  controllers dsL 0/2 | Rev
                                      ^
% Invalid input detected at '^' marker.

R2-Nere#show  controllers dsL 0/2 | i Rev
 FPGA Revision: 0xB2
R2-Nere#show  controllers dsL 0/2

 DSL 0/2 controller DOWN
 SLOT 0: Globespan xDSL controller chipset
 DSL mode: Not Trained
 No frame mode configured
 Line Re-activated 0 times after system bootup
 LOSW Defect alarm: ACTIVE
 CRC per second alarm: ACTIVE
 Line termination: CPE
 FPGA Revision: 0xB2

        Current 15 min CRC: 0
        Current 15 min LOSW Defect: 0
        Current 15 min ES: 0
        Current 15 min SES: 0
        Current 15 min UAS: 0

        Previous 15 min CRC: 0
        Previous 15 min LOSW Defect: 0
        Previous 15 min ES: 0
        Previous 15 min SES: 0
        Previous 15 min UAS: 0

 Line-0 status
 Chipset Version:  0
 Firmware Version:  R3.0.1
 Modem Status:  un checked mode, Status DF3D
 Last Fail Mode:  No Failure status:0x0
 Dying Gasp: Present


R2-Nere#show  controllers dsL 0/2 | i Firm
 Firmware Version:  R3.0.1
R2-Nere#show  controllers dsL

 DSL 0/2 controller DOWN
 SLOT 0: Globespan xDSL controller chipset
 DSL mode: Not Trained
 No frame mode configured
 Line Re-activated 0 times after system bootup
 LOSW Defect alarm: ACTIVE
 CRC per second alarm: ACTIVE
 Line termination: CPE
 FPGA Revision: 0xB2

        Current 15 min CRC: 0
        Current 15 min LOSW Defect: 0
        Current 15 min ES: 0
        Current 15 min SES: 0
        Current 15 min UAS: 0

        Previous 15 min CRC: 0
        Previous 15 min LOSW Defect: 0
        Previous 15 min ES: 0
        Previous 15 min SES: 0
        Previous 15 min UAS: 0

 Line-0 status
 Chipset Version:  0
 Firmware Version:  R3.0.1
 Modem Status:  un checked mode, Status DF3D
 Last Fail Mode:  No Failure status:0x0
 Dying Gasp: Present


R2-Nere#
R2-Nere#
% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]:
% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]: yes

At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system

Would you like to enter basic management setup? [yes/no]:



Press RETURN to get started!


*Mar  1 00:00:07.564: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Mar  1 00:00:21.367: %SYS-3-NOELEMENT: data_enqueue:Ran out of buffer elements for enqueue
-Process= "<interrupt level>", ipl= 6, pid= 3
-Traceback= 80F791B0 80410240 801F7060 801F7144 801E1B1C 801F424C 801F424C 801E1BDC 801F405C 801F75AC 80F8A200 80F8B5D4 80F8AB74 81ECD37C 81CB4DA4 81CB4E5C
*Mar  1 00:00:27.108: %SYS-6-LOGGERSTART: Logger process started
*Mar  1 00:00:27.400: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:00:27.400: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar  1 00:00:28.402: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
*Mar  1 00:00:28.402: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
*Jan 19 05:08:47.055: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T1
Router>1, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Thu 24-Aug-06 17:56 by dchih
*Jan 19 05:08:47.055: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Jan 19 05:08:47.087: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down
*Jan 19 05:08:47.091: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname r1-uppe
r1-uppe(config)#^Z
r1-uppe#
r1-uppe#wr
Building configuration...

*Jan 19 05:09:05.834: %SYS-5-CONFIG_I: Configured from console by console[OK]
r1-uppe#
r1-uppe#
r1-uppe#show vers
r1-uppe#show version | i 12.
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T11, RELEASE SOFTWARE (fc3)
ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-advipservicesk9-mz.123-11.T11.bin"
Cisco 2611XM (MPC860P) processor (revision 0x401) with 124858K/6214K bytes of memory.
Processor board ID FTX1121A219 (2454220871)
r1-uppe#
r1-uppe#show contr
r1-uppe#show controllers ds
r1-uppe#show controllers dsL

 DSL 0/0 controller DOWN
 SLOT 0: Globespan xDSL controller chipset
 No frame mode configured
 Line Re-activated 0 times after system bootup
 LOSW Defect alarm: ACTIVE
 CRC per second alarm: ACTIVE
 Line termination: CPE
 FPGA Revision: 0xA9

        Current 15 min CRC: 0
        Current 15 min LOSW Defect: 0
        Current 15 min ES: 0
        Current 15 min SES: 0
        Current 15 min UAS: 0

        Previous 15 min CRC: 0
        Previous 15 min LOSW Defect: 0
        Previous 15 min ES: 0
        Previous 15 min SES: 0
        Previous 15 min UAS: 0

 Line-0 status
 Chipset Version:  1
 Firmware Version:  A29733
 Modem Status:  un checked mode, Status F5B9
 Last Fail Mode:  No Failure status:0x0
 Dying Gasp: Present


r1-uppe#
r1-uppe#
r1-uppe# show ver | i 12.
Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T11, RELEASE SOFTWARE (fc3)
ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-advipservicesk9-mz.123-11.T11.bin"
Cisco 2611XM (MPC860P) processor (revision 0x401) with 124858K/6214K bytes of memory.
Processor board ID FTX1121A219 (2454220871)
r1-uppe#
r1-uppe#controller DSL 0/3/0
           ^
% Invalid input detected at '^' marker.

r1-uppe#   mode atm
               ^
% Invalid input detected at '^' marker.

r1-uppe#! Change to CPE on other end
r1-uppe#   line-term co
            ^
% Invalid input detected at '^' marker.

r1-uppe#   dsl-mode shdsl symmetric annex A
            ^
% Invalid input detected at '^' marker.

r1-uppe#   line-rate auto
            ^
% Invalid input detected at '^' marker.

r1-uppe#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
r1-uppe(config)#controller DSL 0/3/0
                                 ^
% Invalid input detected at '^' marker.

r1-uppe(config)#   mode atm
                       ^
% Invalid input detected at '^' marker.

r1-uppe(config)#! Change to CPE on other end
r1-uppe(config)#   line-term co
                       ^
% Invalid input detected at '^' marker.

r1-uppe(config)#   dsl-mode shdsl symmetric annex A
                     ^
% Invalid input detected at '^' marker.

r1-uppe(config)#   line-rate auto
                       ^
% Invalid input detected at '^' marker.

r1-uppe(config)#controller DSL 0/2
                                 ^
% Invalid input detected at '^' marker.

r1-uppe(config)#do show run
Building configuration...

Current configuration : 768 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname r1-uppe
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
!
ip ips po max-events 100
no ftp-server write-enable
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
controller DSL 0/0
 line-term cpe
!
controller E1 1/0
!

r1-uppe(config)#controller DSL 0/0
r1-uppe(config-controller)#   mode atm
r1-uppe(config-controller)#   dsl-mode shdsl symmetric annex A
*Jan 19 05:16:29.120: %CONTROLLER-5-UPDOWN: Contro   line-term co
r1-uppe(config-controller)#controller DSL 0/0
*Jan 19 05:16:35.911: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, cha   dsl-mode shdsl symmetric annex A
r1-uppe(config-controller)#   mode atm
*Jan 19 05:16:41.024: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed st   line-rate auto       r1-uppe(config-controller)#
r1-uppe(config-controller)#
*Jan 19 05:16:51.249: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
r1-uppe(config-controller)#^Z
r1-uppe#
r1-uppe#
*Jan 19 05:16:54.991: %SYS-5-CONFIG_I: Configured from console by console
r1-uppe#
R2-Nere#
R2-Nere#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R2-Nere(config)#controller DSL 0/3/0
                                 ^
% Invalid input detected at '^' marker.

R2-Nere(config)#   mode atm
                       ^
% Invalid input detected at '^' marker.

R2-Nere(config)#! Change to CPE on other end
R2-Nere(config)#   line-term co
                       ^
% Invalid input detected at '^' marker.

R2-Nere(config)#   dsl-mode shdsl symmetric annex A
                    ^
% Invalid input detected at '^' marker.

R2-Nere(config)#   line-rate auto
                       ^
% Invalid input detected at '^' marker.

R2-Nere(config)#interf dsl 0/0
                        ^
% Invalid input detected at '^' marker.

R2-Nere(config)#do show run
Building configuration...

Current configuration : 753 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2-Nere
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
memory-size iomem 10
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
!
!
!
!
!
controller DSL 0/2
 line-term cpe
!
!
!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface Serial0/0
 no ip address
 shutdown
 no fair-queue
!
interface FastEthernet0/1
 no ip address

R2-Nere(config)#interf dsl 0/2
                        ^
% Invalid input detected at '^' marker.

R2-Nere(config)#contr dsl 0/2
R2-Nere(config-controller)#   mode atm
R2-Nere(config-controller)#contr dsl 0/2
*Dec 16 03:26:35.571: DSL 0/2 gsi_shdsl_set_frame_mode(): mode change
*Dec 16 03:26:36.135: DSL 0/2 gsi_shdsl_set_frame_mode(): mode change
*Dec 16 03:26:36.163: DSL 0/2  xdsl_mode_commandDownload indication
*Dec 16 03:26:36.167: DSL 0/2 process_get_wakeup
*Dec 16 03:26:36.167: DSL 0/2 xdsl_background_process:Download boolean event received
*Dec 16 03:26:36.167: DSL 0/2 xdsl_controller_reset: cdb-state=down
*Dec 16 03:26:36.167: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, changed interf dsl 0/2
*Dec 16 03:26:36.167: DSL 0/2 gsi_shdsl_reset()
*Dec 16 03:26:36.167: DSL 0/2  xdsl_gsi_int_disable(true):: 0x0
*Dec 16 03:26:36.171: DSL 0/2 xcvr_ptr=825577F0
*Dec 16 03:26:36.275: DSL 0/2 Func:gsi_shdsl_shutdown, Line184fail to abort for shutdown
*Dec 16 03:26:36.319: DSL 0/2  SHDSL Line activation started, please wait
*Dec 16 03:26:36.319: DSL 0/2 DSP interrupt enabled
*Dec 16 03:26:36.319: DSL 0/2 Framer interrupt disabled
*Dec 16 03:26:36.319: DSL 0/2
*Dec 16 03:26:36.319: Setting GTI_NTR_LOCAL_OSC
*Dec 16 03:26:36.323: DSL 0/2  xdsl_gsi_int_disable(false):: 0x1
*Dec 16 03:26:36.387: DSL 0/2  dsp interrupt-download next block for line-0
*Dec 16 03:26:36.411: DSL 0/2 framer intr_status 0xC0
*Dec 16 03:26:36.511: DSL 0/2  dsp interrupt-download next block for line-0
*Dec 16 03:26:36.519: DSL 0/2 framer intr_status 0xC0
*Dec 16 03:26:37.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:38.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:39.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:40.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:41.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:42.323: DSL 0/2 process_get_wakeup
*Dec 16 03:26:43.323: DSL 0/2 process_get_wakeup^Z                                   ^
% Invalid input detected at '^' marker.

R2-Nere#u
*Dec 16 03:26:43.643: %SYS-5-CONFIG_I: Configured from console by consolen all
All possible debugging has been turned off
R2-Nere#
*Dec 16 03:26:44.323: DSL 0/2 process_get_wakeupconf t
Enter configuration commands, one per line.  End with CNTL/Z.
R2-Nere(config)#   line-term cpe
                       ^
% Invalid input detected at '^' marker.

R2-Nere(config)#   line-
R2-Nere(config)#   line?
line

R2-Nere(config)#   line ?
  <0-70>   First Line number
  aux      Auxiliary line
  console  Primary terminal line
  tty      Terminal controller
  vty      Virtual terminal
  x/y      Slot/Port for Modems

R2-Nere(config)#control
R2-Nere(config)#controll
R2-Nere(config)#controller ds
R2-Nere(config)#controller dsL 0/2
R2-Nere(config)#controller dsL 0/2
R2-Nere(config-controller)#   line-term cpe
R2-Nere(config-controller)#   dsl-mode shdsl symmetric annex A
R2-Nere(config-controller)#controller dsL 0/2
*Dec 16 03:27:23.067: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, chainterf dsl 0/2
R2-Nere(config-controller)#   line-rate auto
R2-Nere(config-controller)#
*Dec 16 03:27:38.211: %CONTROLLER-5-UPDOWN: Controller DSL 0/2, changed state to down^Z
R2-Nere#
R2-Nere#
R2-Nere#sh
*Dec 16 03:27:39.475: %SYS-5-CONFIG_I: Configured from console by consoleow run | se DSL
controller DSL 0/2
 mode atm
 line-term cpe
 line-mode 2-wire line-zero
 dsl-mode shdsl symmetric annex A
 line-rate auto
R2-Nere#
r1-uppe#show run | se DSL
controller DSL 0/0
 mode atm
 line-term co
 line-mode 2-wire line-zero
 dsl-mode shdsl symmetric annex A
 line-rate auto
r1-uppe#
r1-uppe#debug xdsl
r1-uppe#debug xdsl ?
  application  xDSL application
  driver       xDSL driver
  eoc          xDSL eoc
  error        xDSL error

r1-uppe#debug xdsl error
xDSL error debugging is on
r1-uppe#debug xdsl dri
r1-uppe#debug xdsl driver
xDSL driver debugging is on
r1-uppe#debug xdsl app
xDSL application debugging is on
r1-uppe#
*Jan 19 05:20:07.863: DSL 0/0 process_get_wakeup
*Jan 19 05:20:08.865: DSL 0/0 process_get_wakeup
*Jan 19 05:20:09.866: DSL 0/0 process_get_wakeup
*Jan 19 05:20:10.868: DSL 0/0 process_get_wakeupdebug xdsl app
*Jan 19 05:20:11.869: DSL 0/0 process_get_wakeup
*Jan 19 05:20:12.871: DSL 0/0 process_get_wakeupno debug xdsl app
xDSL application debugging is off
r1-uppe#
*Jan 19 05:20:13.873: DSL 0/0 process_get_wakeupno debug xdsl error
xDSL error debugging is off
r1-uppe#
r1-uppe#
r1-uppe#
r1-uppe#debug xdsl error
xDSL error debugging is on
r1-uppe#
*Jan 19 05:21:22.629: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:22.637: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:28.030: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:28.038: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:33.467: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:33.491: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:33.567: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:33.587: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:33.688: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:33.696: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:36.484: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:36.488: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:36.785: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:36.801: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:37.157: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:37.169: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:39.798: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:39.802: DSL 0/0 framer intr_status 0xC0
r1-uppe#   line-rate auto
*Jan 19 05:21:53.260: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:53.264: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:53.704: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:53.712: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:53.905: DSL 0/0  dsp interrupt-download next block for line-0
*Jan 19 05:21:53.909: DSL 0/0 DSP interrupt disabled
*Jan 19 05:21:53.909: DSL 0/0  Download completed for line-0
*Jan 19 05:21:53.913: DSL 0/0 Framer interrupt enabled
*Jan 19 05:21:53.913: DSL 0/0 framer intr_status 0xC0
*Jan 19 05:21:53.913:  DSL 0/0 controller Link up! line rate: 2304 Kbps

'''*Jan 19 05:21:53.917: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to up'''
*Jan 19 05:21:54.017: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:54.017: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.021: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.113: DSL 0/0 framer intr_status 0xC1
*Jan 1conf tSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.113: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.133: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.133: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.133: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.209: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:54.209: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.209: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.225: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.229: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.229: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.305: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:54.305: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.305: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.321: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.325: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.325: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.418: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.422: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.422: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.514: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.518: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.518: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:54.522: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:54.522: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:54.522: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.009: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:59.009: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.009: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.013: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.017: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.017: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.021: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.021: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.021: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.105: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:59.105: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.105: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.121: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.125: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.125: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.201: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:59.201: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.201: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.217: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.221: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.221: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.298: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:21:59.298: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.298: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.314: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.318: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.318: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:21:59.322: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:21:59.322: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:21:59.322: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1un all
              ^
% Invalid input detected at '^' marker.

r1-uppe#
*Jan 19 05:22:04.005: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.009: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.009: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.013: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:04.013: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.013: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.013: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.109: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:04.109: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.109: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.125: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.129: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.129: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.206: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:04.206: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.206: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.222: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.226: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.226: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.302: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:04.302: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.302: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.318: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.322: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.322: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:04.326: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:04.326: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:04.326: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1^Z
r1-uppe#un all
All possible debugging has been turned off
r1-uppe#
*Jan 19 05:22:09.005: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:09.005: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:09.005: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:09.009: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:09.014: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:09.014: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:09.018: DSL 0/0 framer intr_status 0xC4
*Jan 19 05:22:09.018: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:09.018: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:09.102: DSL 0/0 framer intr_status 0xC1
*Jan 19 05:22:09.102: DSL 0/0  xdsl_gsi_int_disable(true):: 0x0
*Jan 19 05:22:09.102: DSL 0/0  xdsl_gsi_int_disable(false):: 0x1
*Jan 19 05:22:09.118: DSL 0/0 framer intr_status 0xC4
r1-uppe#
r1-uppe#show ip interf bri
Interface                  IP-Address      OK? Method Status                Protocol
ATM0/0                     unassigned      YES unset  initializing          down
FastEthernet0/0            unassigned      YES unset  administratively down down
FastEthernet0/1            unassigned      YES unset  administratively down down
r1-uppe#
r1-uppe#
*Jan 19 05:22:20.396: %LINK-3-UPDOWN: Interface ATM0/0, changed state to up
*Jan 19 05:22:21.398: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to up
r1-uppe#
r1-uppe#
r1-uppe#show ip interf bri
Interface                  IP-Address      OK? Method Status                Protocol
'''ATM0/0                     unassigned      YES unset  up                    up'''
FastEthernet0/0            unassigned      YES unset  administratively down down
FastEthernet0/1            unassigned      YES unset  administratively down down
r1-uppe#
r1-uppe#
r1-uppe#show atm vc
           VCD /                                        Peak  Avg/Min Burst
Interface  Name         VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts
r1-uppe#
r1-uppe#show run | sec ATM
interface ATM0/0
 no ip address
 no atm ilmi-keepalive
r1-uppe#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
r1-uppe(config)#interf atm 0/0
r1-uppe(config-if)#no ip address
r1-uppe(config-if)# load-interval 30
r1-uppe(config-if)# no atm ilmi-keepalive
r1-uppe(config-if)# clock rate aal5 8000000
                                          ^
% Invalid input detected at '^' marker.

r1-uppe(config-if)# clock rate aal5 ?
        1000000
        1300000
        1600000
        2000000
        2600000 (default)
        3200000
        4000000
        5300000
        7000000

  <1000000-7000000>  clock rates in bits per second, choose one from above

r1-uppe(config-if)# clock rate aal5 7000000
%ATM0/0 Resetting interface...
r1-uppe(config-if)#
*Jan 19 05:25:37.235: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
*Jan 19 05:25:37.752: %LINK-3-UPDOWN: Interface ATM0/0, changed state to down
*Jan 19 05:25:38.753: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to down
r1-uppe(config-if)#no  clock rate aal5 7000000
%Defaulting to 2600000 bps
%ATM0/0: Bringing interface up...
r1-uppe(config-if)#
*Jan 19 05:25:54.752: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
r1-uppe(config-if)#
r1-uppe(config-if)#show ip interf bri
                     ^
% Invalid input detected at '^' marker.

r1-uppe(config-if)#do show ip interf bri
Interface                  IP-Address      OK? Method Status                Protocol
ATM0/0                     unassigned      YES manual down                  down
FastEthernet0/0            unassigned      YES unset  administratively down down
FastEthernet0/1            unassigned      YES unset  administratively down down
r1-uppe(config-if)#
r1-uppe(config-if)#show atm vc
                     ^
% Invalid input detected at '^' marker.

r1-uppe(config-if)#do show atm vc
           VCD /                                        Peak  Avg/Min Burst
Interface  Name         VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts
r1-uppe(config-if)#do show run | sec ATM
interface ATM0/0
 no ip address
 load-interval 30
 no atm ilmi-keepalive
r1-uppe(config-if)#
*Jan 19 05:27:02.142:  DSL 0/0 controller Link up! line rate: 2304 Kbps

*Jan 19 05:27:02.142: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to up
r1-uppe(config-if)#
r1-uppe(config-if)#interf atm
*Jan 19 05:27:30.408: %LINK-3-UPDOWN: Interface ATM0/0, changed state to up
*Jan 19 05:27:31.410: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to up0/0
r1-uppe(config-if)#interf atm 0/0.1 po
r1-uppe(config-if)#interf atm 0/0.1 poi
r1-uppe(config-if)#interf atm 0/0.1 point-to-point
r1-uppe(config-subif)#ip address 1.1.1.1 255.255.255.0
r1-uppe(config-subif)#pvc 2/100
r1-uppe(config-if-atm-vc)#  vbr-rt 2000 2000
r1-uppe(config-if-atm-vc)#  oam-pvc 0
r1-uppe(config-if-atm-vc)#  encapsulation aal5mux ip
r1-uppe(config-if-atm-vc)#^Z
r1-uppe#
r1-uppe#
*Jan 19 05:28:37.839: %ATM-5-UPDOWN: Interface ATM0/0.1, Changing autovc 2/100 to PVC activated.
*Jan 19 05:28:37.839: %ATM-5-UPDOWN: Interface ATM0/0.1, Changing autovc 2/100 to PVC created.
*Jan 19 05:28:37.839: %SYS-5-CONFIG_I: Configured from console by console
r1-uppe#show atm vc
           VCD /                                        Peak  Avg/Min Burst
Interface  Name         VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts
0/0.1      1              2   100  PVC    MUX      VBR    2000   2000     0   UP
r1-uppe#
R2-Nere>ena
R2-Nere#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R2-Nere(config)#
r1-uppe#show running | sec ATM
interface ATM0/0
 no ip address
 load-interval 30
 no atm ilmi-keepalive
interface ATM0/0.1 point-to-point
 ip address 1.1.1.1 255.255.255.0
 pvc 2/100
  vbr-rt 2000 2000
  oam-pvc 0
  encapsulation aal5mux ip
 !
r1-uppe#
R2-Nere(config)#interf atm 0/2
R2-Nere(config-if)# load-interval 30
R2-Nere(config-if)# no atm ilmi-keepalive
R2-Nere(config-if)#exit
R2-Nere(config)#interf atm 0/2.1 point
R2-Nere(config)#interf atm 0/2.1 point-to-point
R2-Nere(config-subif)#ip address 1.1.1.2 255.255.255.0
R2-Nere(config-subif)# pvc 2/100
R2-Nere(config-if-atm-vc)#  vbr-rt 2000 2000
R2-Nere(config-if-atm-vc)#  oam-pvc 0
R2-Nere(config-if-atm-vc)#  encapsulation aal5mux ip
R2-Nere(config-if-atm-vc)#^Z
R2-Nere#
R2-Nere#
*Dec 16 03:39:25.327: %SYS-5-CONFIG_I: Configured from console by console
R2-Nere#show atm vc
           VCD /                                        Peak  Avg/Min Burst
Interface  Name         VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts
0/2.1      1              2   100  PVC    MUX      VBR    2000   2000     0   UP
R2-Nere#ping 1.1.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms
R2-Nere#show atm vc
           VCD /                                        Peak  Avg/Min Burst
Interface  Name         VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts
0/2.1      1              2   100  PVC    MUX      VBR    2000   2000     0   UP
R2-Nere#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R2-Nere(config)#line vty 0 15
R2-Nere(config-line)#login
% Login disabled on line 66, until 'password' is set
% Login disabled on line 67, until 'password' is set
% Login disabled on line 68, until 'password' is set
% Login disabled on line 69, until 'password' is set
% Login disabled on line 70, until 'password' is set
% Login disabled on line 71, until 'password' is set
% Login disabled on line 72, until 'password' is set
% Login disabled on line 73, until 'password' is set
% Login disabled on line 74, until 'password' is set
% Login disabled on line 75, until 'password' is set
% Login disabled on line 76, until 'password' is set
% Login disabled on line 77, until 'password' is set
% Login disabled on line 78, until 'password' is set
% Login disabled on line 79, until 'password' is set
% Login disabled on line 80, until 'password' is set
% Login disabled on line 81, until 'password' is set
R2-Nere(config-line)#passw
R2-Nere(config-line)#password cisco
R2-Nere(config-line)#
R2-Nere(config-line)#
R2-Nere(config-line)#^Z
R2-Nere#
R2-Nere#
*Dec 16 03:40:12.839: %SYS-5-CONFIG_I: Configured from console by console
r1-uppe#show ip interf bri
Interface                  IP-Address      OK? Method Status                Protocol
ATM0/0                     unassigned      YES manual up                    up
ATM0/0.1                   1.1.1.1         YES manual up                    up
FastEthernet0/0            unassigned      YES unset  administratively down down
FastEthernet0/1            unassigned      YES unset  administratively down down
r1-uppe#1.1.1.2
Trying 1.1.1.2 ... Open


User Access Verification

Password:
R2-Nere>exit

[Connection to 1.1.1.2 closed by foreign host]
r1-uppe#
r1-uppe#show atm vc
           VCD /                                        Peak  Avg/Min Burst
Interface  Name         VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts
0/0.1      1              2   100  PVC    MUX      VBR    2000   2000     0   UP
r1-uppe#
r1-uppe#
Retrieved from "http://catch-up.cnap.hv.se/wiki/index.php?title=DSL-cards&oldid=3770"
Personal tools
Namespaces

Variants
Actions
Navigation
Tools