RPi Bluetooth

From Datateknik
Revision as of 13:35, 21 May 2018 by Imra (Talk | contribs)

Jump to: navigation, search

hello

Contents

Bluetooth

Scanning BLE

Scanning BLE is from https://elinux.org/RPi_Bluetooth_LE

device testing

  1. Check what devices you've got
    lsusb
  2. Basic installation checks: The Pi 3's built-in Bluetooth adapter is called hci0. You can check it is operating correctly with the command:
    hciconfig
  3. If you are on a laptop two(2) hci devices will show up, the first one is buggy
    hciconfig hci0 down
  4. Now you can try scanning for BLE devices
    hcitool lescan

Python programs

  1. do stuff
    sudo apt-get install python-pip
    sudo apt-get install libglib2.0-dev
    sudo pip install bluepy
    blescan

Creating a channel, capable of 6lowPAN (IPv6)

[RFC7668] "IPv6 over Bluetooth LE is dependent on both Bluetooth 4.1 and IPSP 1.0 or ..."


Reading http://blog.bluetooth.com/bluetooth-meet-the-internet-internet-say-hello-to-bluetooth you find that BLE uses Generic Attribute Profile (GATT) which is modular, and not Generic Access Profil (GAP) which is static and used by Bluetooth Classic.

GATT has many forms of which one is Internet Protocol Support Profile (IPSP) (Beware of HTTP Proxy Service (HPS) which is something completely different

Picture http://blog.bluetooth.com/~/media/images/blog%20images/migrated/smarthomerouter-01.ahsx (IPv6-BLE switch -> Gateway -> IPv6-Wifi-Bulb == All Native IPv6)

Command for setting what I am (IPSP)

lsmod | grep 6lo
 modprobe bluetooth_6lowpan
 echo 1 > /sys/kernel/debug/bluetooth/6lowpan_enable
 modprobe bluetooth_6lowpan
 lsmod | grep 6lo
   bluetooth_6lowpan 24576 0
   6lowpan 36864 8 nhc_udp,nhc_routing,nhc_mobility,bluetooth_6lowpan,nhc_fragment,nhc_dest,nhc_hop,nhc_ipv6
   bluetooth 552960 32 btrtl,bluetooth_6lowpan,btintel,bnep,btbcm,rfcomm,btusb
 
 hciconfig hci0 leadv
   LE set advertise enable on hci0 returned status 12
> #hciconfig hci0 lestates 
> Read LE supported states on hci0 returned status 12  

Yep, 0x0c or 12 is for unsupported command. So the fw doesn't seem to 
have support for LE. 
Let me get back to you on this, need to check up what fw is upon the repository. 

Command for viewing other end capabilities (IPSP ??)

 hcitool lescan
 LE Scan ...
 CB:AF:14:57:D8:6E (unknown)
 CB:AF:14:57:D8:6E Test IPSP node
  \-- from http://docs.zephyrproject.org/samples/bluetooth/ipsp/README.html

Local setup: NOT WORKING !!

#!/bin/sh
. ./ibeacon.conf
echo "Launching virtual iBeacon..."
sudo hciconfig $BLUETOOTH_DEVICE up
sudo hciconfig $BLUETOOTH_DEVICE noleadv
sudo hciconfig $BLUETOOTH_DEVICE leadv 0
sudo hcitool -i hci0 cmd 0x08 0x0008 1e 02 01 1a 1a ff 4c 00 02 15 $UUID $MAJOR $MINOR $POWER 00 00 00 00 00 00 00 00 00 00 00 00 00
echo "Complete"

Setting an IPv6 address

following the lowpan 802.15.4 blog

  • add
    apt-get install libnl-3-dev
  • This is a strange page
    https://devzone.nordicsemi.com/f/nordic-q-a/14292/iot-sdk-rpi3---using-jessie-with-bluetooth_6lowpan
    • that says:
      root@raspberry:/home/pi#
      root@raspberry:/home/pi# lsmod | grep 6lo
      root@raspberry:/home/pi# modprobe bluetooth_6lowpan
      root@raspberry:/home/pi# echo 1 > /sys/kernel/debug/bluetooth/6lowpan_enable
      root@raspberry:/home/pi# modprobe bluetooth_6lowpan
      root@raspberry:/home/pi# lsmod | grep 6lo
      bluetooth_6lowpan 24576 0
      6lowpan 36864 8 nhc_udp,nhc_routing,nhc_mobility,bluetooth_6lowpan,nhc_fragment,nhc_dest,nhc_hop,nhc_ipv6
      bluetooth 552960 32 btrtl,bluetooth_6lowpan,btintel,bnep,btbcm,rfcomm,btusb
      root@raspberry:/home/pi#

Now to establish my Bluetooth connection between the Raspberry Pis I run though the following steps: On the Master device I run the following commands:

#need root access
sudo su

#enable 6lowpan over Bluetooth le
echo 1 > /sys/kernel/debug/bluetooth/6lowpan_enable

#start advertising Bluetooth LE service
hciconfig hci0 leadv

On the Slave device I run the following commands:

#need root access
sudo su

#enable 6lowpan over Bluetooth le
echo 1 > /sys/kernel/debug/bluetooth/6lowpan_enable

#establish le connection to master
hcitool lecc 5C:F3:70:XX:XX:XX

The hcitool lecc command always returns “Connection Handle 64”. At this point I have a stable connection between the two devices that I can verify using the hcitool con command.

I am now able to run the following command on either the master or the slave where the mac address is the address for the Bluetooth device I am connecting too:

echo “connect 5C:F3:70:XX:XX:XX 1” > /sys/kernel/debug/bluetooth/6lowpan_control

Whichever Raspberry Pi I run the command on establishes a 6lowpan connection and if I run the ifconfig command I see a new bt0 device.

Programming in python

från tysk sida

https://forum.fhem.de/index.php?topic=68019.15


Hi und danke erstmal,

bin jetzt soweit mit fast allen befehlen durch 

Code: [Auswählen]
pi@raspberrypi:~ $ ls -l /dev/ser*
lrwxrwxrwx 1 root root 7 Feb 28 23:59 /dev/serial0 -> ttyAMA0
lrwxrwxrwx 1 root root 5 Feb 28 23:59 /dev/serial1 -> ttyS0

das sieht schon mal gut aus, lt. deinem Howto
allerdings bekomme ich dennoch kein Device : 

Code: [Auswählen]
pi@raspberrypi:~ $ hcitool dev
Devices:
pi@raspberrypi:~ $ hcitool scan
Device is not available: No such device
pi@raspberrypi:~ $ 

glaub bin zu müde oder zu blind.
habt Ihr eine Idee ??

danke


pi@raspberrypi:~ $  systemctl status bluetooth
● bluetooth.service - Bluetooth service
   Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled)
   Active: active (running) since Do 2017-03-09 22:05:23 CET; 22s ago
     Docs: man:bluetoothd(8)
 Main PID: 794 (bluetoothd)
   Status: "Running"
   CGroup: /system.slice/bluetooth.service
           └─794 /usr/lib/bluetooth/bluetoothd
pi@raspberrypi:~ $ sudo service bluetooth status
● bluetooth.service - Bluetooth service
   Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled)
   Active: active (running) since Do 2017-03-09 22:05:23 CET; 27s ago
     Docs: man:bluetoothd(8)
 Main PID: 794 (bluetoothd)
   Status: "Running"
   CGroup: /system.slice/bluetooth.service
           └─794 /usr/lib/bluetooth/bluetoothd

pi@raspberrypi:~ $ sudo hciconfig dev
Can't get device info: No such device

pi@raspberrypi:~ $ sudo bluetoothctl
[bluetooth]# agent on
Agent registered
[bluetooth]# default-agent
Default agent request successful
[bluetooth]# scan on
No default controller available
[bluetooth]# exit
Agent unregistered


pi@raspberrypi:~ $ dmesg | grep Blue
[   22.873317] Bluetooth: Core ver 2.22
[   22.873369] Bluetooth: HCI device and connection manager initialized
[   22.873381] Bluetooth: HCI socket layer initialized
[   22.873389] Bluetooth: L2CAP socket layer initialized
[   22.873408] Bluetooth: SCO socket layer initialized
[  103.040851] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[  103.040860] Bluetooth: BNEP filters: protocol multicast
[  103.040871] Bluetooth: BNEP socket layer initialized






so alles was mit Bluetooth zu tun hat gelöscht und folgendes getan

Code: [Auswählen]
sudo apt-get install raspberrypi-sys-mods

sudo apt-get --reinstall install pi-bluetooth

sudo shutdown -r now


dann 

Code: [Auswählen]
sudo systemctl start hciuart.service
pi@raspberrypi:~ $ systemctl status hciuart.service
● hciuart.service - Configure Bluetooth Modems connected by UART
   Loaded: loaded (/lib/systemd/system/hciuart.service; disabled)
   Active: active (running) since Fr 2017-03-10 00:17:11 CET; 5s ago
  Process: 951 ExecStart=/usr/bin/btuart (code=exited, status=0/SUCCESS)
 Main PID: 962 (hciattach)
   CGroup: /system.slice/hciuart.service
           └─962 /usr/bin/hciattach /dev/serial1 bcm43xx 460800 noflow -



und siehe da!!!

Code: [Auswählen]
pi@raspberrypi:~ $ hcitool dev
Devices:
	hci0	B8:27:EB:90:BC:6D

es geht!!

danke an alle!
Personal tools
Namespaces

Variants
Actions
Navigation
Tools